Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
I have a question about that code, when I test my code with lightblue, it showed me that there is an service called application notification client service, but it didn't...
I'm using GPIOTE library to check the change of two switch inputs.
Normally it works well, but rarely GPIOTE_IRQHandler become never happen even if the pin level changes...
Hi Nordics!
I am using app_pwm.c file in SDK 8.1, and when I use it with softdevice(advertising or data transfer event), sometimes pwm signal is reversed.
I guess, reversed...
Hi Guys,
I am using a the 350Mhz Analog Oscilloscope HM303-6 www.hameg.com/hm303-6.0.html to measure the voltage utilised by the board when it is transmitting data.
...
Hi,
Once I enter into BLE mode I am not able to read any gpios(nrf_gpio_pin_read) also I am not able to set any gpios (nrf_gpio_pin_set).
Below is my example
uint8_t...
I'm trying to establish a bond in my project and then perform service discovery, however the discovery is returning the BUSY error.
I tried to wait for the events according...
In SDK 8.0 the bare word asm was re-introduced in nrf_delay.h , causing failures in compilations that use strict C/C++ standard conformance flags. This was noted in earlier...
Hello Developers
I have to solve a problem for which I could not find much information about online, so I am hoping you guys can help me.
I am developing a WIN32 application...
Hello, For some reason the Ble App Uart is not working on my PC anymore. I have gone over Nordic tutorial again however, the LED doesnt blink and I cant detec the device on...
Hi,
What are the general causes of SDS assert in nrf51/52 ? Assuming that SW has been tested, is there something that could happen in the code that would cause the assertion...
Hi All,
I'm using "scanForPeripheralsWithServices" of iOS to the BLE devices.
"scanForPeripheralsWithServices" sometimes never return anything.
I have to stop scan or...
Hello! I'm trying to build a program for nrf51822 via QT Creator.
I'm using QBS for build. I have a makefile from SDK examples for nrf51822. Someone can help me, how to setup...
Hi all,
I have the exact issue mentioned here - github.com/.../9
I have updated my makefile to generate only one bin file from the Softdevice Hex file, but still I'm getting...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi,
I'm testing the ble_app_beacon on my nrf51422 dk. I followed the instruction in the sdk documentation . All was well. Then, I tried to test with the nrf Beacon app...
