Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
I am having nrf52840 dongle,my purpose is to make it a peripheral device,enable gatt,change tx power through gatt.i uploaded blinky hex code(compiled in vs code ) to the controller...
I am using nRF52833DK, zephyr v2.7.0.
I want to disable hardware nRST to use P0.18 as GPIO.
What I did
Added to Kconfig : CONFIG_GPIO_AS_PINRESET=n
Removed : gpio...
I previously tested the peripheral_ams_client with iOS 17, and I could select the device in iOS Bluetooth settings to connect to it, however it appears in iOS 18 iOS is not...
Dear: We have product using nRF51822 with BLE to UART bridge between an app on the phone and the UART interface on the nRF51822 device. that include control command and OTA...
I want to implement a PWM up/down ramp that preferably runs with no CPU involvement. From the datasheet it seems I can do this by storing a sequence in RAM and having the...
Programmer tool v3.0.9 outputting the error - " Failed to detect device after reboot. Timed out after 10 seconds." After the user attempts to write a blinky hex file to a...
Hi,
My Development Kit is PCA10040, SDK_17.0.2.
I have builded the example code -> \nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132\ses
in...
Hi, I have multiple nRF52840 Dongles and need to set one of them to permanently stay in advertising mode, even if a device disconnects.
If I use the nRF Connect tool to...
Hi,
I click on the device tree editor icon in VS-code and I see nothing
although I have an open working Zephyr nrf connect application in VScode.
I installed nrf...
Hello DevZone,
I'm building a Matter development environment with OTBR and CHIP-Tool:
NB: Ubuntu 22.04 with WIFI and BT, get CHIP tool from official pre-built (V2.5...
I am trying to install the nRF_Connect_SDK and associated toolchain under Linux Ubuntu ARM64. I find from other postings here that nRF_Connect_For_Desktop is not available...
Hi all,
last week i used nrf connect app (v4.28.1) to update firmware
after i pressed DFU button and selected binary file, then it will jump a window to choose like...
We are using a Nordic nRF52840 microcontroller alongside the nPM1300 power management IC. When the battery is switched off due to low voltage (undervoltage protection), the...
Dear Nordic Support Team,
I am reaching out for assistance with an issue I’ve encountered on my new nRF7002DK board. After successfully flashing the Azure IoT Hub example...
I work on NCS 2.8.0
I add follow to CMakeLists.txt
add_custom_target (
my_release_file
echo AAAA BBBB CCCC
DEPENDS all
)
when run "west build -b nrf54l15dk...
