We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
We have a custom board with the NRF52840 running NCS v2.8.0.
We have a problem where our device will crash/lockup. From our testing so far, it seems to be related to Bluetooth...
I have a project for the NRF5340 with SDK 2.6.1. I test the code with twister using Unity and CMock. That works great. But now I have to adapt the unity_cfg.yaml (which is...
Hi,
DK:NRF54L15
Modify form the sample code:peripheral_uart
I add one spi21 and k_timer to get the sensor data, periodically. But got the error ZEPHYR FATAL ERROR 4...
Dear Nordic Support Team,
I am working on a project to measure distance using two E73-2G4M08S1C nRF52840 modules. I would like your guidance on the best approach for implementing...
ide :- segger embedded studio I have a problem regarding BLE_UART.
I am using Segger Embedded Studio. I want to implement Bluetooth, so I used an already existing code in...
I want to do DFU with secure keys on nrf54l15dk. I want to receive in my application new firmware and store it on internal flash of the nrf54l15 (i have memory to store the...
Dear Nordic Support Team,
We are using the nRF5340 together with the NPM1300 in our project. The 1.8V output is controlled via the NPM1300.
When performing a BLE DFU ...
Hi,
Could you please give us some power budget comparison regarding connections using CoAP vs MQTT and other protocols (UDP socket...)?
We are thinking on a nRF9151 design...
Hi all, Relatively quick question. I have a production implementation where the COMP "Cross" event is wired by PPI to a GPIOTE "out" task. The Comp is acting as a UVLO. When...
Using Zephyr V2.8 on the L15. In the uart callback, in the UART_RX_RDY case, can the evt->data.rx.offset ever be non-zero?
It doesn't appear that the offset is ever non...
I am in trying to use the AT client sample with an RS485 interface on a custom Board with nrf9151.
Other than the API states ( https:/https://docs.zephyrproject.org/apidoc...
Hello Nordic Engineer,
Actually, the phones are not part of the mesh network, right? Also, I treat all the nodes inside the red box as LEDs because I'm designing...
My own 52833 board use QFN40 package. DK use aQFN73 package.
I try the same code. and find DK can enable exernal xtal. while my own board cannot enable external xtal.
...
Hi,
I have an Adafruit feather nRF52840, and try to program it via a Nordic DK (through the connector Debug out). It is possible to flash the feather when I use a devicetree...
Hi support team,
I'm currently developing a project for a custom board with a nRF9160 chip and with nRF Connect SDK 2.9.0 and Zephyr 3.7.99 using VS code with nRF connect...
