Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello Everyone,
i'am trying to build my Hello_world application but i'm having some issues and i can't figure it out there's some ninja file whch stopping the build does...
I'm using NRF52840DK, sdk for mesh version 5.0.0, sdk nrf5 version 17.0.2. When i add FreeRTOS into LP example, i have some problem:
I think it problem with timer mesh and...
Dear Members,
Can I merge the code from this example :
E:\nRF5_SDK_17.0.2_d674dde\examples\ant\ant_plus\ant_bpwr\bpwr_rx\main.c , it's using S212
with,
E:\nRF5_SDK_17...
Hi, I'm using the nRF Mesh Library for Android and I'm looking at the data of a mesh network in JSON format. I don't see anywhere the sequence number of a provisioner. Where...
I am following the guide on this page: https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
I can build the firmware, but having trouble...
1， The SDK is nRF5_SDK_14.2.0_17b948a;
2, running the usbd_audio project; It don't control the volume by 52840;
3, Can you help me how to adding the volume control in...
We tried two build options:
1. thread version 1.1 with
# Set OpenThread NCP architecture CONFIG_OPENTHREAD_COPROCESSOR=y CONFIG_OPENTHREAD_COPROCESSOR_RCP=y
CONFIG_OPENTHREAD_THREAD_VERSION_1_1...
Hello
I'm using sdk v17.0.2 and I'm going to program using nrf52840 dongle.
I used nrf52DK because I didn't have nrf52840DK. And I'm going to upload the source code that...
Hi!
I am running Zephyr sample application for direction finding zephyr/samples/bluetooth/direction_finding_connectionless_rx with minor modifications on nRF52833 DK. I...
Hello, I'm developing a BLE application under nRF51422 based on SDK12.2 using softdevice S130. Now, I'm porting the application from Keil to IAR 8.11. There is no compilation...
Hi,
SDK nRF5_SDK_17.0.2
Using :\examples\peripheral\saadc
I want support for multiple peripheral in same project, so i took the saadc example and on top of it add Uart...
Dear Devzone,
We are testing GPS of our products based on nRF9160.
When we test in one car, the GPS signal is lost when the device is put inside this car. This situation...
While testing DFU for OTA ,after entering bootloader mode on my nRF52840 DK, the device doesnt show up either in the device manager or using nRFconnect and Jflash lite . when...
I've 3 FTD nodes (nRF52840 SoC), the network between the nodes and the UDP message transfers are been done successfully.
I want to split and send the messages between...
Hello,
I am using your NRF9160 chip and need Nordic team help. I have refer to your FOTA sample, I am looking for a safer solution for updating code. On my board, I use...
