After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
I'm getting timeout errors when trying to program a Thingy:91 with a J-Link Pro PoE on macOS on an ARM Apple M3 Max.
Here's the command and error message:
I get the...
Hi, can you please help me with configuring ras_initiator for channel sounding when using two antennas on the initiator and one antenna on the reflector ? I am starting from...
Hello,
in the bluetooth mesh section https://www.nordicsemi.com/Products/Wireless/Bluetooth-Mesh
It is stated that BLE MESH and BLE can coexist.
However, I don't find...
I am trying to set up continuous integration using the docker image for NCS v3.0.2 as described here: https://docs.nordicsemi.com/bundle/ncs-3.0.2/page/nrf/scripts/docker...
Hello,
While working with a custom board with nrf5340 and instead of DCDC inductors, has voltage regulators. Why does CONFIG_SECURE_BOOT lock up the custom board but not...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hello NRF Community, I am trying to interface the Adafruit PDM MEMS Microphone (Link: https://www.adafruit.com/product/3492) with my nrf52832dk. However, it fails every time...
In NCS 3.1.x it is now necessary to generate code using the .matter file during the build process. However this is failing on Windows because there is a typo in the chip_codegen...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
I followed the steps below to set up my development environment, based on the instructions from link
Setup 1 1. Installed SEGGER J-Link v8.56a Path: C:\Program Files\SEGGER...
We have this custom sensor board, running nRF9160.
Application code built with SDK 2.5.0, running modem FW 1.3.2, and using LTE-M connecting to MS Azure IoTHub with MQTT...
Hello, I have an application, that uses the Bluetooth to do over the air updates using these two configs:
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Hi all
I’m having a horrible time trying to get an nRF7002EB Wi-Fi coprocessor working with a nRF52840 via QSPI interface in nRF Connect SDK 3.0.2 (Zephyr 4.0.99). I'm using...
Hello,
We are working with Onomondo in integrating their software SIM. We have it working and sending and receiving data, but am having some issues figuring out what is...
Issue Summary: When running west flash to program my board using the UF2 runner, the process fails with an OSError related to copying the .uf2 file to the UF2 bootloader drive...
