But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi all,
I would like to have a semi-duplex communication link over one pin (+GND). The nRF will act as a pure slave device which responds to, and acknowledges, commands...
Hello, we understand that the Nordic framework, by default, restarts advertising on disconnect. I learned that here, thank you:
https://devzone.nordicsemi.com/f/nordic-q...
I'm currently running on nRF Connect SDK (hash: 4b012fb4882f0ddd3de9f339ebc5a3f1c3cacd4a). I'm running a connection between a nRF91+nRF52840 (as central running NUS_C) using...
I have an nRF52840 board that fails to connect to Linux over USB. The board powers on and the green LED at the lower left of the PCA10056 flashes on/off rather quickly. But...
There is a bug in fds.c file, Please go through the below code snippet.
I do not return from fds_gc(), execution stays there for infinite.
More information:
1) #define...
Nordic nRF52840, with regards to stored security keys in flash, some wear leveling schemes move data when being updated but do not erase data from the old location. This is...
Based on several posts I've found on the forum, the notification queue size is automatically set by the stack based on the connection event length (NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hello, I have developed a program that reads (with I2C) a temperature sensor and sends it to the central board. The central board is a NRF52480-DK. I have tested the peripheral...
Dear Sir.
I was testing dfu mode with an nrf52840 dk and held down the IF BOOT/RESET button, then powered up and waited a few seconds before it went into bootloader mode...
Hi,
I'm evaluating the NRF52832 for an ultra low power BLE application where I'm going to use GATT. I've built some prototypes with the NRF52832 and right now I have to...
Our engineers have two questions that they are confused with:
1) When applaying ble techniques, does nodic 52 serious of chip compatible with SIG mesh?
2) When applaying...
Hi there,
we are working on getting type approval certification, and the test lab is asking for fixed frequency software, drivers and SOP.
What we need is the fixed frequency...
Hi,
The actual problem: I want to store some stuff to flash at factory, that is never erased. And I also need another persistent memory that can be written in runtime. I...
Hello I am now trying to implement an active NFC Tag using nRF52832. But I don't know what that example project is. Can you point to a command or example source that performs...