We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi all, I am combining MESH SDK 3.0.0 light switch example client and server with SDK 15.2. I have combined some server code to client and there are no error. And I can use...
hello,
We have developed a custom board corresponding to mbed pca10024 evaluation board.We haven't mounted the rf section and not even the crystal.The only thing that the...
I'm trying to read temperature sensor data through TWI (I2C) from SHT3x using NRF52-DK and SDK v16.0. Observing an oscillator, the address and the return value with CLK looks...
Hello team,
Due to very constricted space on PCB, I am sharing one green LED between to IC's.
U1 is the NRF52832, and U2 is a Lipo Battery Charger IC. I want either one...
Hello,
I am working on the Nordic DFU to develop a bootloader for OTA update on our product.
So far I just ported the Secure Bootloader from Nordic examples. No functionality...
Hello!
I am trying to understand why the HFCLK of the DecaWave DWM1001C module based on nRF52832 has a significant (7000-10000 ppm) frequency offset w.r.t. its nominal value...
Hi
I use SES and nRF52832 dongle . I want to send data on "ble uart" and get that data on "nRF UART v2.0" app. mean i want send a string in program while every 5 second...
I'm working on modifying an existing app written on a custom nRF52832 board. The app uses softdevice s132, and was written for SDK14.2. The app was originally written with...
It seems that the PEER ID is managed by the PEER MANAGER. Can I manage this information myself? For example, I save this information (ADDR IRK) after the connection event...
Using SDK 15.2.0, s132, nRF52-DK.
The logging facility in Segger Embedded Studio tells me that the call to nrf_sdh_enable_request() takes about 500 ms. I have an interrupt...
Hi,
I was following your guide to implement a secure boot chain ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_bootloader.html ) and therefore build...
Hello,
I have a simple question. So, I'm trying to write some manufacturing information into the UICR but once I write to these addresses I can't see the device via bluetooth...
Hello,
I am using the UBLOX EVK-NINA-B406, which has the nrf52833. I have attempted to use Softdevice S140 and S113 (using the nrfConnect programmer. Soft device versions...
I want to interface the nRF5340-PDK board to a different vendor's board that runs at 3.3V.
I'm using the SPI bus to communicate between the two boards
Using the nRF5340...
