This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
We developed a new BLE hardware product using the Laird BL652 third party module. Our product is based on the latest Softdevice S132 V5.0.0.
Now I'm starting the Bluetooth...
I have problems getting the beacon example in the new mesh SDK v0.10.0 working.
I invoke cmake with this command:
cmake -DTOOLCHAIN=gccarmemb -DPLATFORM=nrf51422_xxAC...
Hi there~. This is Matthew! I saw a thread explaining that the production variants of the nRF52840 will first be available Q4 2017 at this link .
I was planning for BLE...
Hi,
I had a difficult problem.
First, S110 & SDK9
ble_stack_init () is the source.
static void ble_stack_init(void)
{
uint32_t err_code;
// Initialize the...
Hi. I'm using nRF51822 as Peripheral.
To init the service for example "NUS", i have to call NUS_BASE_UUID as below..
#define NUS_BASE_UUID {{0x9E, 0xCA, 0xDC, 0x24, 0x0E...
Hey guys,
From what I understand, the minimum connection interval on say, an iPhone, is 20ms. Also, you can send up to 6 packets of 20 bytes within a connection interval...
I have established a ble connection between two dk boards, the code I based on is the ble_app_uart_c and ble_app_uart, and try to detect some rising edge delivered from the...
It's kind of relative question with my previous question.
"When smartphone range is shorter than a peripheral(nRF5X), is there any way to receive an advertisement from the...
Hi all, I tested the example: Experimental: LE Secure Connections Multirole Example with my smartphone and it is working fine, but when I tried use LESC on my peripheral device...
I can't open a com port after starting the nRF Connect app. This happens in Windows (native) and also a Linux virtual host with the com port passed through. I'm using a nRF51...
I found strange behavior when using back-to-back packet transmission.
Configuration of PTX/PRX is:
No Auto-ACK (disabled)
CRC 2 bytes
Packet length 13 bytes
Addr...
I have the blinky examples working, but have not been able to get any example code using any gpio input to work. they compile fine but the buttons done seem to work. I'm using...
Hello,
I'm using the sample project from this post .
Following the steps and using nRF52DK, one for server and one for client. I've modified the server count from 3...
Hi all , I has 3 board : 1 board central connect with 2 board peripheral . I want to send string from peripheral 1 to central , then from central to peripheral 2 . Please...
