After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello,
i just wanted to compile a example project out of the box: ble_app_uart.
S132. SES. PCA10040
Surprice, did not work, why do you provide not working examples...
Trying to use a standard delay function to keep and output low for several seconds. It is P0.10 on the 52840 set to Active Low and I do see it transition to a low on the o...
Dear,
I am using both nRF52840 UART (UART0 and UARTE1) on the nRF52840 DK.
The default pin assignement is used, such as
UART0 pins are TX/RX 0.6 & 0.5 and
UARTE1...
Hi NRF team,
I am working on one project. I have used 2 PDM Microphones (MMICT5838-00-012). And I have used Zephyr RTOS for development.
I have used the LC3 encoding and...
Hi,
I'm working on a project using MCUboot, TFM, and a network core app. We use MCUboot with an external flash module for OTA firmware updates.
Recently, we tried upgrading...
Hi,
I am following DevAcademy Lesson 5, HTTP over Wi-Fi (Exercise 2), which involves adding TLS to an HTTP connection.
When I remove CONFIG_WPA_SUPP_CRYPTO_PSA=y , I am...
Using an nRF54L15 here (if that matters) and adding mcuboot via sys build to my project. Couple questions:
- How would one adjust the logger baud rate to something other...
Hello,
I have the nRF5340 DK and I want to program/debug an external SoC. I see that in order to do that I can use the connector P19 to connect to an external board with...
I am using an nrf5340 DK instead of the audio DK. Is BT LE possible with this DK. Is there any difference beween NRF5340 DK and audio DK in terms of microntroller.
Hello,
I’m using VS Code with the nRF Connect extension. When I try to build the “bme68x_iaq” application to upload it later to the Nordic Thingy:53 and read its data, I...
Hi,
I have verified the firmware upgrade and file transfer functionality from a Linux-based device to the customized nrf52840 board using the mcumgr tool.
However, the...
Hello, everyone!
I'm interested to know about the possibility of mixing BLE audio and custom BLE Characteristic in one single nRF5340 application.
For example, we would...
Hi DevZone Community,
My Envriornment
1.9.1 NCS nRF9160DK Current Modem Version : 1.3.2 This question is involving a device which is in production. The issue is, if the...
Hi folks,
Recently picked up a new MacBook (M series) and was excited to try some sample projects on my nrf52840dk.
Unfortunately upon trying to Debug, I get the following...
Hello Nordic team,
I followed the official guide to add a custom sensor cluster to my Matter application. Everything built and flashed successfully, and the application...
