Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I thought this would be rather simple as I would design a BLE peripheral in the usual way but the source of data for the peripheral comes from a sensor sending nonconnectable...
Hi,
I am exporting SAADC example to NRF52840 Dongle and I can see this structure:
/** * @brief Input selection for the analog-to-digital converter. */ typedef enum { NRF_SAADC_INPUT_DISABLED...
Hi,
I get read service content retained after reset, and it is read by the central before I get the chance to change it. Please advise how to clear it upon restart.
Thanks...
I want to create two switch EP(if it is possible I would like to it as much switches as possible).
I am using WIndows 10 with Segger and nRF COnnect SDK v1.5.0.
I tried...
Hi, We're trying to simultaneously run BLE Eddystone and connectable mode in our application. Our device is advertising it's ID but every time I try to connect via BLE from...
Hi Team,
regarding my application I need to switch the reference voltage we are taking two deferent reference voltage Ex: one for 2.25 and another 0.75 so we have requirement...
Hi,
I am working with nrf52-ble-app-uart-relay example taken from Nordic Playground github. I have SES IDE, nRF5_SDK_16.0.0 & nRF52840 DK. The central part of the relay...
Hi
Having the nRF5340DK board and following few examples from the nRD SDK Connect. After programming the application core, need to program the network core using the hci_rpmsg...
Hi, I already read more threads about this issue. How to program the nRF52840-Dongle. Most threads go to far in details, where my knowledge ends... I just want to run a simple...
I am trying to include software support for the ST LIS2DE12 accelerometer chip which is found in V1.5.0/zephyr/modules/kconfig.st as
config USE_STDC_LISDE12
bool
V1...
Hi,
I'm looking for the source code to the program that came on the Thingy91
I have not been able to find the source anywhere in the documentation
or sample code....
I am trying to port an nRF51 project that runs on the nRF51 DK using Keil to the nRF52840 DK using Segger Embedded Studio. Clearly the best way to start is to take an example...
Hi,
I am using nrf52833 development kit have nRF5_SDK_17.0.2_d674dde with softdevice as s140 when i running the code following error occurs as follows on serial monitor...
Hi
I am facing a problem similar to the one in Case ID228253.
I am using a custom 52810 board and have configured the UART pins on P0.12(Tx) and P0.14(Rx), defined in...
Feeling disappointed while trying to find information on nRF Connect SDK documentation. Let me give this simple example:
Mission: check and ensure that watchdog is enabled...
