i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,
I'm using 52833 and S113.
My system works well, i have all my caracteristic and i'm able to read it out with nRfConnect mobile app.
But it is terribly slow .
I...
I'm using nRF52832 S132 and migrating from SDK 15.2 to SDK 17.0
My previous code used nrf_serial which appears is no longer available in SDK 17. I don't see any info in...
Hello everyone,
I would like to add ble secure bootloader on my NRF52840 dongle, I have already do that with the nrf 52832 DK But there is no example in the SDK for PCA10059...
I need to write received data from SPI to address pointed by a parameter. When doing a transfer, spi drivers also read the data sent by slave during TX. I know this is normal...
Hi all:
I am use ble_app_blinky demo sdk 16.0.0 I want to put system on idle mode,but there need to call two times sd_app_env_wait() so it can in system on idle mode.
...
Hey,
I am a new to BLE devices. I am using BL651 Laird Connectivity's 453-00005 module
and using standalone JLink OB ARM debugger to connect.
When I try to connect my...
Hi,
I want to get running the sample "lwm2m_client" on the board nRF9160DK (PCA10090).
Modem FW Version: 1.2.0.
I build the sample with Segger Embedded Studio v4.52...
Hello,
When I try to run a project containing a .cpp file, I get the following console output:
I am compiling the openthread client example with a slight modification...
Hello, I am trying to change the instance on the spi in the spi example, but unfortunately it is throwing me an error - implicit declaration of function 'NRF_DRV_SPI_INSTANCE_...
Hello,
I am using nRF52840 S140 v7.0.1. I have a query on Tx power settings.
1) In below snapshot under features, its mentioned as “4 dB steps”. So whether can I write...
Hello,
I previously used the latest SDK v17.0 on my nRF52832 PCA10040 board DK.
I ran the ble_app_uart example in order to understand how the Nordic UART Service works...
Hi all
I am doing a small personal project. I have 2 DK's :
nrf51 DK: pca10028
nrf52 DK: pca10040
Up until recently things worked fine, but suddenly i ran into a...
1. At present, using the Programmer burnmodem firmware in tool nRF Connect mfw_nrf9160_1.2.0.zip step is cumbersome.
2. Is there a simpler command line tool that can burn...
