Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
im use the example of nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard
and i change the code of static void hids_init(void) like this:
and...
Hi
i have installed segger emstudio and almost all dependencies but still can't able to build a project. my main target is to work with nrf9160 dk but without an hardware...
Hello!
I'm working on a project with the new nRF5340 & Zephyr and I'm trying to get two SPI peripherals on the same bus sampling data correctly. It's a simple program thus...
Hello,May I ask you a question?
Hardware model: NRF51822 SDK version: SDKv9.0.0 SoftDevice:s110.
I used the interface in the pstorage.c file to realize the storage of...
Hi there,
I'm just trying to start to code my project. I want to stream 48k 16 bit audio from one nrf52840 dongle to the other one. I only need one way transfer.
I have...
Hi,
I want to use dtm project to test RF PHY performance about NRF5340. But after downloading dtm project and empty app project, NRF5340 can work normally from output RTT...
Hello I use nrf52832 and sdk v17.0.
I'm testing the firmware using custom pcb. Sometimes it stops altogether if there is an error in the firmware during the test.
The...
Hi. I'm testing our new product that can be extend ranges using FEM.
For best performance, I'm matching impedance between antenna and FEM.
But my major is not wireless...
Hello, I have a problem with my own designed board, It has nRF52832 and some other sensors which communicate over SPI, also I have a SD card on the same bus that works fine...
Hello,
In my code I am reading from a sensor and want to check if the float value returned is out of range. In order to do so I would like to be able to calculate the absolute...
i have just blinked the LED and trying to pwm
i have written a simple led blinking program like this one below
#include <stdbool.h> #include <stdint.h> #include "nrf_delay...
I'm trying to diagnose frequent (80%) DFU failures that I'm seeing with our Android application using Buttonless mode.
Our target can be 100% reliably updated with our app...
Hello,
I would like to program the NRF52840DK to send ZigBee beacon(not beacon request) to the end devices, but I cannot seem to find the API, etc. to do so.
Or perhaps...
Hello NRF ,
I am not able to run any of the the BLE peripheral example codes from the SDK12.2.0 ( Nordic NRF 52 SDK ) .
The reason I am using 12.2.0 is I have a sensor...
