But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi!
I have been using LoRa for communication for my product. I'm looking into using BLE mesh.
I have a couple of hundred sensors, all 1-2m apart from each other. Here...
In this scheme we use 2 inductor in a serial connection. 15 nH + 10 uH. Total inductor = 10.015 uH. ??? Is really need to add this 15 nH inductor? For why? If we just short...
When calling access_model_subscription_list_dealloc() from models_init_cb() an assert is triggered in sublist_invalidate() due to mesh_config_entry_delete() returning NRF_ERROR_INVALID_STATE...
I have 3 Nordic nrf52840 USB dongles , several Particle Mesh Argons and have ordered an Arduino Nano 33 BLE Sense and have found the Adafruit Feather nRF52840 Express . All...
Hi,
Greetings!
I am facing a issue while updating firmware
My Setup:
SDK 16.0.0
SDK for Mesh 4.0.0
nRF52832
DFU: secure_bootloader_ble_s132_pca10040
Application...
I've gone through the forum and I've tried certain "solutions" but none of them work for me.
I've erased my device in SES multiple times, recreated the files for the service...
Hi all, I am checking the Uart central and peripheral projects, also the one with usbd and I have one question that may be obvious for you. How do you select the peripheral...
Hello,
I am using nrf52840 and SDK 16.0.0
I am doing some work with the calendar example and got some questions.
Q1.
Inside the main function in main.c file there...
Hi, Is it possible to go from slow advertising to fast advertising with a button press? I did this but it didn't work:
P.S. I slightly modified names and operation of my...
Dear,
We just start to development our project. I use the Segger + nrf5_SDK_for_Mesh_v4.0.0.
I open the light switch sample project from "nrf5_SDK_for_Mesh_v4.0.0" by...
HI,
I am working on the interface between the nrf52832 and the MPU9250 IMU.
I have communication working fine with using nrfx_twi, but I have the following error when...
Hi,
I'm writting a simple test code that uses the aplication timer library (app_timer) to wake up from SystemON Idle mode to SystemOn mode every 1 minute. The idea is to...
Hi All,
I wan't to have logging via segger RTT from enabled modules in the MESH SDK.
Tried several config options in sdk_config.h, but without luck.
I made a diff of...
I'm using the app_timer library to create one shot timer. I'm calling the app_timer_start() to the same timer repeatedly in the gpiote handler. I had thought that this would...
Hi ... i want central to connect to the two different peripheral mac address , i am using ble_app_uart_c example version 15.2 .. using scan_filter_address i can abe to connect...
