Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
I've a board with usb port
I can insert on USB the Raytac MDBT50Q-RX containing the nrf52840 and:
- my microcontroller can recognize it as CDC ACM USB serial...
Hi, I'm Developing Custom Board with nRF52832.
When I execute my custom code (by referring to ble_app_template example), an error occured.
First, my hardware spec below...
Hello, i am using the ble_app_beacon example on the nRF52840 DK with s140 and i want to send the service UUID for Device Information. I inserted the code from the ble_app_template...
i'm trying to get samples/drivers/CAN working with the nrf52
apparantly you need to enable CAN explicitly in menuconfig, which is already confusing because prj.conf has...
Hello. I met trouble, presented in the name of the thread. I use example for PCA10400e board. So, what I've changed to accelerate reproducing of this error. I change logger...
I have a question about the current consumption of GPIO and GPIOTE.
I want to use port in input configuration. Therefore, the following settings are made ("P_WUP_BLE"...
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes get an...
HI
We are developing a 2d-3d mouse .
We are trying to implement OTA-DFU into our custom board .
We first tried it on development kit and its working fine too . I can...
Hello all,
Environment:
Rpi with Raspbian Stretch (Release 9.8)
Kernel 4.14.8-v7+
Architecture armv7l
I have followed the below links to build BLE 6LoWPAN environment...
After compiling the SDK 15.2 ble_app_hrs_freertos_pca_10056_s14 example in Segger Embedded Studio there are a number of repeated warnings:
"configTICK_SOURCE" redefined...
Hi,
i've got the TWI scanner example flashed onto the NRF51 dk board, using the default "Arduino" pins of P0.07 and P0.30 as SDA/SCL.
I've added two lines to the example...
I have a small collection of i2c devices on the bus that can be jumpered in (sda/scl disconnected). I am currently using SDK v10 and Keil v4.
I wrote this code to namely...
Hi,
I am trying to use the SSD1306 display with the nRF9160 DK.
I am using the code as is shown here
https://github.com/zephyrproject-rtos/zephyr/tree/master/samples...
hi, thanks for this tutorial : devzone.nordicsemi.com/.../ble-advertising-a-beginners-tutorial
i'm trying it on my nRF52840 devkit board.testing it with nRF connect application...
I have a nordic ble dongle. I want to interface it with an external microcontroller via usb. Is there a set of usb commands that can invoke the softdevice api's in nordic...
