This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I have 3 new Thingys and have connected to two of them using the IOS Thingy app. When connecting, it prompts me to do a firmware upgrade (from v2.1 to v2.2) but when I kick...
nRF Connect log shows DFU mode cannot be achieved. Same test on SDK15.2 worked.
Comparing the ld files of 15.2 and 15.3 shows uicr_bootloader_start_address and uicr_mbr_params_page...
Hi, In SDK 15.3 I have found a bug in internal implementation of the lps22hb external driver. Bug description: Unable to set properly a INT_S[2:1] bits in CTRL_REG3 register...
Hi:
I am having trouble just trying to build the asset_tracker_image.
I followed the instruction on setting the nRF Connect. (nRF Connect v3.2.0). However I got the following...
Hi,
When I reference of SDK Coexist examp of uart for adding in Experimental dimming example.
I get success in it.
I take dimming level from uart, and publish it via...
Hello,
Just received the nRF9160-DK and followed instructions but it seems there is no connection, only LED3 is blinking
Location is Belgium close to Brussels
Hi,
I'm using the PCA10056 dev kit to verify the workings of the DCDC converter. I added the following code after nrf_sdh_enable_request() :
e = sd_power_dcdc_mode_set...
Hi to all,
I'm new with the nRF52 DK developpement board and I use Zerynth ( Python ) for developping a simple application for a product who are still existing. ( MOKO M1...
Hello,
I am developing in Windows 10 machine in visual studio code. I cannot use Seggar studio. Devloping for nRF52840 dongle with nRF15 sdk.
I have written the below...
I am using SDK12.3 and the Flash Storage module to store some data in Flash. I frequently need to update some of these data basing on received commands.
When I use "fs_erase...
Hello,
we are developing a machine that is in pre-production. We need to be able to update the firmware and until now all works well on android. but on IOS the dfu does...
I'm trying to get the LTE Sensor gateway running on the nRF9160 DK. The documentation says to run the HCI:UART example on the nRF52840. When I click on the link for that example...
Hi,
I need to know if it's possible get the firmware work using 52810 with 192K flash. As far as I know, S112 takes 100K, APP with secure connection takes ~85K(ble_app_hrs_pca10040_s132...
nrf52832 S132 v6.1.1
i want to write saadc data in flash, so i call "write_to_flash" function in "void saadc_callback(nrf_drv_saadc_evt_t const * p_event)"
sizeof(data_array3...
Does anyone know if Segger Ozone is licensed for commercial use if used with Nordic Semiconductor devices, similar to the use of Segger Embedded Studio? Or, do we need to...
