We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
When trying to update an app using Secure DFU, we get invalid object error. The error comes from dfu_decode_command.
Using nRF5 SDK 12.2.0 on custom nRF51822 board...
I have followed the CoAP example from IoT SDK,
I have a Raspberry PI set up as the router,
and two nRF52 boards, one is the client, the other is the server.
Following...
I have following questions:
Is there an example for implementing WeChat on a nRF52?
Is the nRF52 module supported for WeChat AirSync?
Where can i finde the requirements...
Hello!
I'm drawing a circuit with nrf52840 chip and I want to ask some questions:
Is it ok to use 2-side pcb (not 4)? what's of these better in part of radio communication...
Hi, I use nrf connect to programing demo board nrf51 dongle to get it work, failed.
error log as follows:
2017-03-02T09:30:20.014Z INFO Application data folder: C:\Users...
Hi,
Does the PPI module automatically clear the event flags for the linked event? For example, if I have the following:
NRF_PPI->CH[0].EEP = (uint32_t)&(NRF_GPIOTE->EVENTS_IN...
hi
I'm porting Arduino code which has calls to ShiftIn() to read a byte from a GPIO Pin and bitWrite() to write a bit into a byte variable at a particular position.
Below...
dear friends,
now i need to let a master 52832 device communicate with multiple slave 52832s.how can i make it? Our scenario is that a teacher takes a phone in a classroom...
I used SDK12.2.0 and S130 develop with 51422;
I want to test for fds write and read, I followed the fds_sample from github; it can write success, but no FDS_EVT_WRITE return...
I have to exchange information with smart cellphone. My 10040 board create a pair of key by micro-ecc and transfer the public key to the cellphone. However, the cellphone...
i am using timer 1 of nrf24le1.for which i have calculated a value which is to be loaded in th1 and tl1 for 1ms .calculations are as,
clock =16mhz;fosc=16mhz/12=1.333mhz;t...
Hey everybody, I'm having 'intermittent' issues with device addresses on the nRF24L01+. I've read the documentation on what you're not supposed to do as far as device addressing...
dear friends,
There is a pic that i catched using sniffer. SlaveLatency,a gap parameter,is set to 2.As you can see, when the slave do not give an ack,the mater will resend...
