Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I'm trying to run the vanilla HTTPS sample on the nRF9161 DK: sdk-nrf/samples/net/https_client/README.rst at 4b9841a28e97e9d61b93f8981375d644b9d04ea0 · nrfconnect/sdk-nrf...
I need to install the Direct Test Mode App to validate the direct test mode running on a custom board. On the version 5.1.0 of nRF Connect for Desktop all app installations...
Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
I am trying to use my nRF52840 as a sniffer and am attempting to follow the directions at:
Programming the nRF Sniffer firmware (nordicsemi.com)
Note that I have downloaded...
Hi,
I want to use a LNA for make our sensitivity better, Then i should to put a RF switch and have a control in sending and receiving, because when the device is in receiving...
I am developing a USB dongle (nRF52833) for computers and a controller (nRF52833). As a basic configuration, multiple controllers need to be connected to one dongle. Multiple...
Hi,
We have a custom board (powered by nRF52840 with Softdevice and nRF5 SDK 16) that has an external ADC module to sample 30 kHz ADC continuously for 1-2 seconds. What...
I encountered the problem trying a Matter OTA-update and and asking myself why the bootloader wouldn't apply the image:
I am using the partition manager and defining the...
After flashing the nRF Sniffer for Bluetooth on nRF52840 dongle, I want to flash it back with the programmer to use it in the nRF Connect App but it wont go in boot mode....
Hi. I did some testing with two nrf5340DK boards to check the accuracy of distance measurement with Nordic's nrf_dm app. Even in non-high precision mode the reading with ifft...
Hi.
Our company has a couple of different custom designed boards using the nRF52840 and powered by a battery. OpenThread is used for networking, and the devices are configured...
Hello, I got a custom board based on nRF52840. It uses extended BLE advertising to deliver a sensor data to the central hub with a frequency of 10 Hz. I've set the interval_max...
I have a question regarding DTM using nRF Connect for Desktop. It is my understanding that the signal generated does not have a BLE packet structure but it is a continuous...
Hello. I have been playing with the HID keyboard example (./samples/subsys/usb/hid-keyboard) and it's not running correctly. Code was compiled for the nRF7002-DK board (-b...
