Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
ble_gatt_db.h and ble_db_discovery.h each contain #defines that are problematic, BLE_GATT_DB_MAX_CHARS and BLE_DB_DISCOVERY_MAX_SRV respectively.
Of course, one can change...
We use NRF52832 in the remote control of the car。 We measured the average current of power consumption at about 1uA.Every 300ms, the current curve bounces to the transient...
I would like to use the RTC in the nRF52833 as a clock-calendar. The device will normally be powered by the USB Vbus but must have power fail protection to insure the integrity...
Hello,
I would like to create a star network (with no routers) in ZigBee with nRF52 (also with multiprotocol BLE). I examined the relevant SDK (nRF5_SDK_for_Thread_and_Zigbee_v4...
My setup is a custom board with the nRF52832 and a remote BLE client e.g. nRF Connect tool kit on an Android phone.
The application periodically broadcasts a 'beacon' but...
I am using Nordic SDK v15.3.0.
I have set all the required parameters and content before I call the API "ble_advdata_encode(..)". I ran into two issues one of which I can...
I am using SDK version 15.3.0 and would love to know what exactly is the meaning of the first parameter "size of event" used in the macro APP_SCHED_INIT(X,Y)?
I treat "events...
I have installed Segger Embedded Studio for ARM V5.32a.
I am trying to build the example project under ble_peripheral/ble_app_uart.
I have installed these packages in...
Dear community, Dear Nordic engineers,
For some reason I cannot connect my custom board to the nordic cloud. Previously I have followed the described procedures with the...
Hello,
I have a custom nrf52832 board with a SparkFun HX711 load cell.
I've developed my firmware using Segger Studio testing my data through a BLE connection with the...
Hi,
I ported my application from SDK 12.3 to SDK 17.0.2. Unfortunatley it isn't running on the board, but the only thing I have is a warning which I'm hoping is the issue...
Hello,
Let me start with some background information and end with some questions.
Background
We are using the 9160 in cat-m0 and locking to AT&T and Verizon bands...
How much is the temperature characteristic improved by setting CALIBRATE OFFSET for nRF52832? How much does CALIBRATE OFFSET improve the temperature characteristics?
Are...
Hi. In other discussion I have seen pairing/bonding should store all necessary parameters of a discovered service. It's possible then to reconnect to a bonded device without...
