Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello
I use nrf52832 and SDK v17. And I'm using NUS (UART) service and peer manager. So far, I've been testing with an Android phone and connected it with an iPhone for...
Hi All,
I have modified ARM FB ABI type preprocessor macro to "soft" to optimize power consumption in my saadc routines. But I am seeing below error while compiling. I...
I am developing USB CCID driver class for nordic nRF52840. I used USB CDC-ACM class as reference and tried to implement for USB CCID. I have developed the device descriptor...
Hi,
I have a question of correct way to connect/disconnect/reconnect from the LTE network to save power.
I already know about PSM mode.
But In south korea, SK telecom...
Hello
I'm working on SDK v17, and I'm using the nRF52832 custom board. I use several APP_TIMERs. One of those timers doesn't seem to be working properly. Timer calls are...
I'm just finishing a BLE project for a client. The code is based primarily on examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput. I'm using SDK 15...
Hi there,
We're using NRF52840 and nRF5_SDK_15.3.0_59ac345. We have a product where 2 nRF52840's have to talk to 1 device (say, an iPhone or a computer). We were thinking...
I've noticed when using the nRF Connect Software, after I connect to a perihperal, it immediately discovers services, but takes about 4 seconds to read the GAP Device name...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hello,
What the average data consumption for using A-GPS on the nRF9160 to download the Almanac and Ephemeris data? I would like to know how much data is billed through...
Hi,
I am developing a product based on SDK v15.3.0 and SoftDevice v6.1.1. my product acts as a BLE central device.
On the peripheral side, is an iOS application which...
Hi,
I need some help in explaining the GPS behaviour I am observing. In the following figures the GPS current draw is depicted.
For the specific scenario the position...
Hi,
I'm testing stability of my firmware. As a part of tests I'm trying to maintain long term (multiple days) connection between nRF52 and nRF Connect for Android app running...
Hello, i have a routine that updates the firmware in Application Core flash. It works erasing the flash and receiving the srec data with TWI slave (waiting for USBD).
Now...
Hi, I have developed an application for nrf52810 and now it needs an additional feature of saving several integer values to flash, so they are available even after power loss...
