Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
We have implemented proprietary audio streaming on the nRF52. It reads Audio from a PDM mic and uses the timeslot feature of the BLE radio to send said audio to another BLE...
Hi:
I already updated the SDK to the first release version V1.0.0 and the unit works well with NB-IoT, UART and SPI. I'd like now to include real GPS data but I can't get...
Hello, I'm working on programming a cycle to measure the power consumption. I need to send a message and wait for a response for some time, then shut the modem off, no matter...
Hi,
We were planning to use a spectrum analyser in order to do the radio test on the nrf52-dk. Where should the analyzer be connected? Should it be connected to the J1...
Hello, I'm trying to test the UART example for nRF 9160 DK. To my understanding, any input sent through one of the ports should appear in the other one (from uart1 to uart0...
I would like to use PSM to save power consumption of nRF9160 LTE module. However, if I use PSM on the module, the module is dormant and not able to receive the command from...
Hi, this might be a trivial question but I'm struggling to find the solution. I want to configure the asset tracker application so that it works with real GPS data on the...
hello!
i am using my nrf52832 with s132 softdevice. basically the ble template with my services and charas.
i checked power consumption in sleep mode and observed something...
Adding a Network Coding Extension to CoAP for Large Resource Transfer
https://ieeexplore.ieee.org/document/7796871
Can I use this coding in your some SDK project?
...
Hi all,
I ned to test DTM in labview. In nRFgo Studio works fine, but I don't have any idea hoe to relize same test in labview. Could anyone help me please?
Thank you...
Hi,
I'm working on nrf9160 DK board version 0.8.5. I want to use analog pressure sensor and read data using GPIO input, however there is a little issue related to acceptable...
Hi,
I'm having issues maintain the connection to a MQTT server. I'm able to establish the connection, keeping this alive and pub/sub some massages, but after some time ...
Hello ?
I try to bluetooth 5.0 Le mode test
but nrf studio program is not supporte Le mode 2M bps
therefore i need to nRF DTM Tool for bluetooth 5.0 LE mode 2M bps test...
Hey, When I initialize the device information service as follow ，It seems that It does not work ，RTT View show There cause a Fatal error 。 But if I initialize one of them...
