This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello ?
I try to bluetooth 5.0 Le mode test
but nrf studio program is not supporte Le mode 2M bps
therefore i need to nRF DTM Tool for bluetooth 5.0 LE mode 2M bps test...
Hey, When I initialize the device information service as follow ，It seems that It does not work ，RTT View show There cause a Fatal error 。 But if I initialize one of them...
Hi, I'm provisioning mesh nodes using nrf_mesh APP. After I finished it and added device into mesh network, I have some questions in configuration process.
In nrf_mesh APP...
When I send AT command, AT+COPS?, in example, +COPS: 0,2,"26201",7 will be returned. In this example, it returned one numeric string for MCC and MNC.
Can I simply read this...
Hi,
I don't find any information on the antenna used on the nRF51 DEVELOPMENT KIT. The chip is N51422.
I would like to have information like the gain of the antenna. Could...
Hi,
I'm Trying to add uart with DMA functionality to the asset tracker sample code.
but when running :
I get:
this is my nrf9160_pca10090ns.overlay :
these...
Hi Roshan
I want to use ViewModels in RecyclerView like I have to perform light on/ off (sendGenericOnOff(final boolean state, final Integer delay) android app)r each node...
Hi all,
I am running thethings.io examble of Thread SDK 3.1
I setup border router (Raspi 3B + NCP + ethernet) , Node (NRF52840DK)
In Node, I can ping to thethings.io...
Hello,
I'm currently a student and new to RTOS and modems in general, so please excuse my possibly very basic questions.
We have a running demo with an ESP32, where...
Hello everyone,
We are using the nrf52840 Dev Kit (PCA10056 1.1.0 2019.19 683465548)
SDK version: 15.3
OS: Fedora
We have our program working fine (RTT Logs OK...
I followed the install instructions from nRF Connect SDK documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_ins_linux.html ), to build and...
I have nRF52832 board. I had interfaced nRF52832 board with STEVAL-IDP005V1 for FFT analysis. I am getting all the data and messages in STEVAL-IDP005V1 - UART (in PC). When...
Hi Team,
I working on the python script were i am trying to connect multiple nrf52 devices. nrf connect app for windows is connecting to multiple devices which is fine...
Hi,
We are designing a system using nrf52840, in which we intend to keep the wall clock time with battery support.
Reading about the internal RTC module, it gives an impression...
