Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi Team, Currently we are working with nrf52832 in one of our project and now we are going through FCC for the same. I am using radio tool code(SDK 15.3) to generate the FCC...
hey
I am using the timeslot API to be able to access the CCM peripheral while using the soft device.
For my application the nrf52dk needs to go into sleep mode and wake...
hi, i want to update firmware by OTA from sdk11.0.0_89a8197 to SDK_15.2, but can not scucess.
i tried follow command to build a zip file.
nrfutil pkg generate --hw-version...
Hello,
Here's my current setup:
I am using the nrf52840 SoC for development, which as I understand, has 2 UART instances available. One instance is being used for a third...
Hi
i am using the nrf52832 dk.
I am trying to combine the ble_app_uart code along with the fds code using ses.
what are the changes i have to make in the config file...
I changed the I2C pins to below, and it not work. so is it possible to reconfigure the I2C pin? what should I do since I already set to 8&9 in the hardware board? const nrf_drv_twi_config_t...
Hi,
Looking for some ground on getting the netowork parameters set for a zigbee device, My intention is to limit the number of scan intervals and the scan time to save power...
I'm planning wireless conference system. This needs some condition as under simultaneously use 5ch of wireless bi-directional connection through whole system. Each wireless...
Hi,
I am using nRF52832 soc to develop my project. with nRF5_SDK_15.3 . SES file
I need to connect both BMI160 accelerometer sensor and AT24C512 EEPROM ic in TWI.
how...
I am trying to update firmware that uses v14 of the nRF5 SDK to firmware that uses v15.3, but I am getting the error "Init command larger than expected.".
I'm wondering...
Hello everyone,
I'm running the IoT CoAP example on my nrf52840 Development Kit.
The border router is Rapberry 3 B+ on Jessie with Kernel version 4.19.46. I've put BLE_6LOWPAN_LEGACY_MODE...
I am using nRF5SDKforThreadandZigbeev300d310e7 sdk for thread example simple_coap_client. I try to add uart module with simple_coap_client and i have added uart configuration...
Hi,
I am running nrf52840 on a custom board, SDK 15.0.0, softdevice S140 6.0.0 and SES.
In my application I am reading an IMU ( ICM20602) and a laser ranger/Time of Flight...
hi,master.
Question 1: In Asia, the speed of accessing web pages is slow. SDK15 development documents can only be accessed online on the official website, but often cannot...
