Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I want to undestand this. I can't see any examples with it. In the example ble_app_proximity I always received 100% level.
If it possible, can anybody give a ADC config example...
I am working with a Blend Micro Board (Arduino IDE with RBL_nRF8001 sdk), using
Evothings.
Using the RedBearLab Simple control example I can easily connect to the board...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
Hi all,
I measured the delays between a GPIOTE event and a Task (in this case toggling with another GPIOTE) through PPI.
The results are showed below:
For the...
Hello, I followed from the link . I successfully program bootloader, and bootloader setting and program. And my program is working fine.
But I cannnot update from DFU. Everytime...
Hi,
I am working on with nrf52 with SD132 v2 SDK11 since we need serial bootloader.
I tried a gattc long write sequence to write 22 bytes. Everything works well, peer...
OpenThread recently merged a DNS client into the main branch. DNS would be extraordinarily useful because my code accesses content behind load-balancing servers with dynamics...
In this example code:
nRF5_SDK_13.0.0_04a0bfd/examples/ble_peripheral/ble_app_proximity/main.c
Where the ADC is configured to read the battery voltage:
nrf_saadc_channel_config_t...
Hi,
I've read a couple of threads in this forum that suggested that the DEVICE_MANAGER_APP_CONTEXT_SIZE value (which should be a multiple of 4) is supposed to be 16 bytes...
We're using the nrf51 with the RFAxis (now Skyworks) 2401C amplifier, which is a fixed gain 20dBm amplifier. The goal is to have a longer range 'beacon' type product and the...
What would be the best BLE Library or Framework for Raspberry-pi to exchange with nordic?
I'm trying to get data from the NRF51's GATT data.
But there are no reference...
I recently was trying to test my nrf52 DK. After lot of failed attempts i was able to do DFU update over BLE and also Serial upload .
I am now trying to test the BLE UART...
Hi
According to previous answers ( 1 & 2 ), the limitation on the maximum number of devices that can be added to a whitelist is 8, and is due to softdevice timing limitations...
I have downloaded the nRF51 SDK from here www.nordicsemi.com/.../nRF51822 and I'm trying to run HCI-UART examples as explained here developer.nordicsemi.com/.../a00063.html...
