Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I'm using a nRF51422+nRF6310 and I need to use SPI in order to connect with some devices. I am trying to run the example "spi_master_example_with_spi_slave" but I found...
Hello, I'm using IAR for ARM 7.1.
I made my own project and I want to make my project as a hex file to
program my application to several boards.
/***************...
Hi, i am currently modifikat a working ANT-System (Master with multiple Slaves) with the NRF51422 and Softdevie 1.0 to be robust against in band disrupters. My idea is to...
I have an application based on the ble_HID_keyboard_template (uses STM32F072 instead of Arduino). The first time I pair my iPhone 5 (iOS 8.1.1) with the nRF8001, everything...
Hi,
I'm using nRF51422 with S310 and ble_app_hrs example application.
Thus I can simulate a Heart Rate Sensor with the board and get data on an Android phone with the...
Hi all! May I use another quartz instead of 16 MHz? Will the output frequency equal to 2.4GHz/16, if I will be use the 1 MHz quartz? Or IC will not work? Is it possible to...
I need to evaluate the real consumption of current for BLE events on RF81822. The HFCLK is 16MHz and the 32kHz clock is external.
S110 Soft Device Specification V1.2 document...
Hi, I am using S120 1.0.0 and SDK 6.0.0. Learning the sample project 'ble_app_multilink_central'.
I already got a peripheral device with NUS service. The central device...
I am new to this great platform and am struggling with getting my PIR sensor connected to my DK. I wonder if some of you experts could give me some pointers on how to go about...
Hello, I build a BLE 6LoWPAN environment on my raspberry pi with Kernel 3.18.3 and connect a BLE Dongle. The BLE Node is Arch BLE ( www.seeedstudio.com/.../Arch-BLE-p-1998...
Hi, I have two different types of nRF24L01+ modules, both behave differently.
The "troublesome" module always has TX_DS asserted after a transmit, which is the same behavior...
Hi,
I am using the SPI Master 1 to control an EEPROM. I used the spi_example project to help get the code working. It all works fine if the code that initiates the SPI...
We have designed a differential antenna for the nRF51822 CEAA chip.
Each of the RF output connects through a matching circuit to each one of the two 50-ohm to ground end...
How to setup MQTT for CloudMQTT? I have working raspberry PI I can ping and connect to device when follow the user guide. Now I like to try MQTT example but don´t know how...
