After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
What would be the best way to plot RSSI levels in dB versus distance using the distance measurement sample code? I see that the default code gives an RSSI open space measurement...
Encountered an issue while programming the nRF5340:
It was working fine before, but after connecting to RTT, a pop-up prompted some encryption option which I didn't read...
Two days ago, I bought a set of ppk2. in the process of use, the host computer software prompts "Device must be programed do you want to procced?", when I click "yes", the...
https://github.com/NordicDeveloperAcademy/ncs-fund/blob/main/v2.9.0-v2.7.0/l4/l4_e1_sol/src/main.c
The current logic uses i and j to calculate factorial.
for (i = 1;...
Hi:
I use sdk nRF5_SDK_17.1.0_ddde560. bootloader use examples\dfu\secure_bootloader\pca10056_uart_debug.
It cann't enter the application.
But If I use examples\dfu...
Hi,
I'm currently trying to write a simple Wi-Fi driver code that can connect to my Wi-Fi network. I'm building for the nrf7002dk_nrf5340_cpuapp and am using NCS v2.5.3...
I want to use the radio test code from the nrf example library to tune the nrf52833 on a custom board. I managed to build and flash the project, but when connecting to the...
Hi,
I have been evaluating some Nordic Semiconductor products for the past week. They look great.
I am using the nRF5340 Dev Kit, along with Visual Studio Code on...
As stated in the title, when I set CONFIG_CHIP_FACTORY_DATA_BUILD to n , the following compilation error occurs.
However, if I keep it as y , the MCU fails to function...
Is a Zigbee Direct SDK available for Linux which could be used to allow it to act as a Zigbee Virtual Device (ZVD) using Bluetooth LE?
I am particularly interested in the...
I am measuring latency using the nrf5340_audio with SDK 2.8.0. The measurement points are the analog input on the gateway side and the analog output on the headset side. I...
Hi!
I am using v2.6.1/nrf/samples/bluetoothdirection_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data...
Hi support team,
I'm currently developing a project that requires enabling FCB (for dps to Azure IoT Hub) and LittleFS to store data on an external flash. However I cannot...
academy.nordicsemi.com/.../
The comparison of "increment_count + decrement_count != COMBINED_TOTAL" happens after test_mutex unlock. It is possible that between comparison...
