i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Good evening, I determined the numbers of clocks necessery to fire up an interrupt from an GPIOTE event. My debugger reports 1373 clocks ticks to go into and go back from...
Hi,
What is the maximum ATT MTU size for the BLE NUS?
While programming my BLE NUS server application I constantly ran into the problem that my MTU and length updates...
Hello,
am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0.
I am working with PPI, GPIOTE and 2 timers (called timer1 and timer2) on nrf52832
Through the COMPARE...
Hi,
I am trying to use BlueZ in "Raspberry Pi 3B" to connect my 51822/52832 device.
My Hardware is Raspberry Pi 3 model B, and use internal bluetooth interface, the OS...
Hi Nordic gays guys,
After our 51822 firmware added the Service Changed characteristic.The Android OTA GATT_ERROR issue was solved.But there is a new problem in IOS.After...
Hi,
Find big problem with GCC make settings (guess Makefile.common) does not work with SDK 15. with SDK 14.2 same Project works succes.
The Problem : use SDK15 , the...
Hi,
Not directly related to Nordic, but I as many people are doing the same I figured it's fine.
is there any reason why this would not work? assuming the I2C is already...
Hello,
I just bought an nrf51822 evaluation kit and a segger J-link BASE Jtag. I understand that I have to play with the SW4 swith and the U4.
I identified the switch...
Hi
I am trying to setup my raspberry pi to receive message from Arduino using C++ code. I am getting a below error message. pi@raspberrypi:~ $ sudo g++ -Wall -Ofast -mfpu...
Hi I just have a simple question and that's where the code keeps Bluetooth mesh control how many devices it has in its stack that it has provides keys to. for every time I...
hi
sdk 15.0,
IN Multilink, 15 devices is operate normally. However, changing the device to 20 causes problems.
Is there a way to fix the problem?
attached source ...
Hi,
I was trying out the long range example provided on the NordicPlayground GitHub repo, and worked great when communicating between two nRF52840 dev kits. I however noticed...
I know that the the +/-250ppm LFRC accuracy is required for BLE... but is that just for a system that receives data? Is there any need to calibrate for a system that only...
Hi all,
I am using PCA10040 with nRF5_SDK_14.2.0 and using the ble_app_uart example.
Basically I have a large array of size 18750 to send out and having read on the forum...
