Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I have nrf52 Thingy board and i want to read temperature sensor data using twi sensor example available in SDK 11. I am not able to get data.
Thanks
Hi Support team,
I am looking to replace my BLE chip by a nRF8001. I am currently using a DA14580 (Dialog Semiconductor), in Beacon mode or pairing mode. I saw that the...
Hi,
As given in the link: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools%2Fpower_profiler_kit%2FPPK_user_guide_Troubleshooting...
Hi, would you support with the following:
In the high voltage mode (defined as when the supply voltage is only connected to the VDDH pin and the VDD pin is not connected...
(Overview) When accessing the I2C device connected to the Nordic controller nRF 52832, The CLK frequency changes during the process, resulting in operation at an unintended...
I have the nRF52 Dev Kit running now on Mac OS with SES.
(for reference to this topic: click here )
My end result is to use the nRF52 chip as part of a MIDI wind controller...
Dear All,
I am looking for EMI/EMC testing for my custom board based on nRF52832 board. Could you please provide any generic firmware for the same. Is there any UI to test...
Hi
I have my application running on nRF52 on SDK 11 (Softdevice S132 version 2.0). I am using 1 peripheral and 6 central links in my application. I am migrating the application...
HI, i have a small question. When I downloaded the hardware files of thingy52, and opened altium files, I can not move components in a pcb layout, i have to split windows...
Hi,
To decrease the load on the system I would like to periodically send some BT data (and do some SD card writing).
Since Timer 0 is used by the soft device, I am using...
I want an amplifier to receive audio from a FM/DAB receiver and from an NRF52832 that - in turn - has received audio over BLE. The amplifier should either receive the radio...
when I start to program nRF52832 under 1.8v some memory pages can't be accessed. this is short listing:
Erasing page at address 0x78000. Erasing page at address 0x79000...
Hello,
I'm trying to make some current measurement using the nRF6707 and a nRF5 SDK Board(10040) (Board out of the box, shunts untouched).
We're facing problems measuring...
Hello,
Does the newest SoftDevice release v5.1.0 support the advertising data length extension (255 bytes)? If not, will it be available this year?
We are at the evaluation...
Hi,
I am using nRF52832 DK (PCA10040) SDK 14.2.0 and S132 V5.1.0.
I am planning to test the TWI loopback (in order to familiarise the APIs used for TWI in nRF52).
I...
