Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hello,
I have some problem with a specific phone. I try to connect with the nrf52832 using samsung S3 with android version 5.1, the connection takes 20 - 50 seconds and...
Hi,
I am very new to nrf51822 controller. I Used STM32 cortex controller's.
I want to know basic hardware which are the require to start nrf51822 working and programming...
The example nRF51-DK gerbers have solder mask on the PCB antenna. But for the nRF24L01+ EK gerbers, the PCB antenna has the solder mask removed partially, along the length...
Hi,
I downloaded the nrF5 SDK V12.2 from:
www.nordicsemi.com/.../nRF5-SDK
after unzip, I could see the SDCard library under "\nRF5_SDK_12.2.0_f012efa\components\libraries...
Following III. Example code and Enabling whitelisting ,
I try to connect to the "nRF52 DK" board with a whitelist (Android BLE device address),
but I've never connected...
1、I use SDK9.0 ANCS project, the position is as follows:
SDK9.0\examples\ble_peripheral\ble_app_ancs_c\pca10028\s110\arm4
2、I need a project which is contained with...
hello there,
i am giving external supply to nrf51. my external supply is usb 3.3 v. but when i connect it with nordic and then if i check it on multimeter , it shows me...
Hi all,
Does anyone know how much current is meant to be drawn to discover nearby devices? I guess, in other words, how much current is drawn to put the nRF51822 in discovery...
Hi Sir,
I have a NRF 51822 board & MPU 9250 sensor.
I want to read YAW,PITCH,ROLL,ACC_X,ACC_Y,ACC_Z,GX,GY,GZ,MX,MY,MZ values from MPU Sensor.
Could you please share...
Hi All,
Continuing on with my project: a custom board containing nRF52 + ECG front end.
Successfully integrates SPI functionality; need 2 more interfaces:
32...
Previously you recommended using S132 v4.0.0 2. alpha release to get more than 8 central connections. As far as I know this revision doesn't implement Bluetooth 5.0 protocol...
Hi,
I have written a code which transmits data over BLE.
The board was getting reset.
What we changed is instead of sending application data we sent the RESETREAS register...
Hi,
I'm trying to change the MAC address of nrf52, using softdevice s132_nrf52_3.1.0 but we dont have sd_ble_gap_address_get() and sd_ble_gap_address_set() APIs in "ble_gap...
We are having a random current leakage problem with our nRF51822 based board. Normally, our board and the application consumes around 10 uA of current. However, too often...
For example, I have the following code:
bool interruptFlag;
void interruptHanler(void)
{
interruptFlag = true;
}
void main(void)
{
while (true)
{
if (interruptFlag...
