Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
on iOS 9 beta 5, ANCS doesn't work.
Steps to reproduce:
On iPhone, Settings -> Bluetooth
Tap to connect and pair
Make a phone call on another device
no caller...
Good work,
I am trying to control with android i nrf51822 But I have a problem. Ten LEDs After connecting the device with Android when I press the off button or "device does...
redbearlab nrf51822 led controller with android.nrf51822 with android connected.But led on off Device does not support uart.Disconnecting.
How solving is the problem ?
I wrote code usenig de Development Board 10028 (nrf51422).
I bought in aliexpress This model link text
The first question I remember There is almost no difference between...
I have a project, where I try to trigger an interrupt when I get a low-to-high tranistion and high-to low transition.
My setup:
-nRF51DK
-SDK8.1
-SoftDevice 8...
I'm looking at the ble_app_hrs example and I'm confused about how the drivers are able to differentiate between events originating from various services/characteristics. For...
The JLINK is costs hundreds of dollars, the STLINK is less thank $20 USD (available on ST's Discovery boards). I would really prefer to use the STLINK. Is there a way to program...
I have two nRF24L01+, one as PTX and one as PRX.
Both have following config: EN_RXADDR = ERX_P0, EN_AA = ENAA_P0, RF_CH = 100, RF_SETUP = 0x26, SETUP_RETR = 0xF0, SETUP_AW...
Hello, i have bought nRF51822 pcb module on Aliexpress (nRF51822 CEAA chip HWID 006A, 16Mhz crystal) and I'm trying to test it with SDK 6.1.0 and S110 v. 7.3.0 (as compatibility...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
Hello,
Using BLE Scanner app (available for Android), i'm able to change the device name. I can also write other values for each characteristic.
How can we protect a...
Hi,
I use nrf51822 with SDK8.1, S110 and gcc with Makefile. I want to use nrf_drv_twi in both my main “.c” file as well as a library “.c” file that is included in the build...
This is SDK 8.1.0, Softdevice 7.3.0 (not being used for this demo), running on a NRF51822-CEAA.
The minimal program below just sets the WDT for 10 seconds, then goes into...
