Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Hello,
While I am creating a new projects. I am getting an error message. I don't know the path of the files . I randomly created a project in D drive ,c Drive . So My question...
There are the following projects under the Health Thermometer example for Keil
What is the difference between them when trying to install on the nRF51 DK? I could not find...
Two (2) nRF52840 DKs, SDK 17.0.2
I believe I have added the necessary code from ble_blinky_apps both peripheral and central to their respective NFC reference role examples...
Dear Sir/Madam,
I'am new to segger embedded studio.I would like to do SPI interfacing of an IC using nRF51822 with segger embedded studio.
Please guide me how to add...
Zephyr version: 2.4.99
OS: Linux
Board : nrf9160dk
I am trying to read data on UART 1 with interrupt. I have below shown portion in my code for enabling UART 1. (I...
Hi, I need to Interface the 2.4" SPI TFT Module ILI9341 Driver with nRF52832
I came across that in Peripheral/ GFx Example will run. once I build and run the project My...
Hi Dev Team,
I was working on the Nordic Thingy91 and had to establish an external communication of a sensor to the Thingy91 through a UART.
For this, I was looking into...
Hi,
My PC is Windows 7 64-bit and my tool is J-Link V9. The CPU at my target board is nrf52840. I use nRF connect desktop version 3.60 and it works fine. I got the upgrade...
I have the driver setup like all of the other sensor drivers I'm using, but I can't seem to find a device tree or Kconfig
This should be enabled by the CONFIG_SOC_NRF52840_QIAA...
Hello!
We have a custom board connected to a battery and a USB cable
Our fw calls:
NRF_POWER -> SYSTEMOFF = 1 ;
The board turns off.
And then we remove the USB...
Nordic's smart remote 3 is for nrf52832 and nrf52810.
I want to port the same on the nrf52840 DK.
I have basic IR receivers and Transmitter and want to integrate them...
I'm using the nrf52832 from fanstel (bt832) to stream audio to the adau1701 dsp. I want to be able to play music over Bluetooth. I'm using i2s to transfer the data to the...
Hello,
I am trying to change PHY after packet sent/received (known as asymmetric PHY).
After receiving EVENT_END, i write to register MODE to change the PHY.
This can...
Hi ,
I am using saadc to measure battery voltage i m using the sample example given as reference ble_app_proximity/
I am doing adc_configuration in one file and triggering...
