Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I need to save energy for my ble application. So I turned off the sensor when there was no ble connection. A ble connection is a condition for me to turn on the sensor, but...
How exactly are the UART pins selected for the nRF9160? I've searched and am unable to find a file to configure pins. I need to change to pins from the development board to...
Hi,
I'm working with the SAADC on an NRF52832. I'm using the SAADC driver from SDK15.2.
I have a problem with the calibration routine because it's generating DONE events...
Hello,
I am developing an application on the 52840 and so far find the SDK documentation quite confusing and somewhat contradictory. I need to write a simple TWI (I2c) master...
Hi, I’m located in Liège, BELGIUM.
Using the nRF9160DK, an orange SIM card, MODEM firmware mfw_nrf9160_0.7.0-15.alpha I managed to make run some sample code:
mqtt_simple...
Hi. I'm using nRF52832, SDK13.0.0.
The roll is peripheral.
And I'm using Oberon to use ECDH.
I think you have the result or document for random generator's performance...
The nRF9160 DK I'm working on does not seem to be able to connect to nRF Cloud after following the tutorial:
https://www.nordicsemi.com/Software-and-Tools/Development-Kits...
Apologies, I accidentally closed and opened my previous ticket: https://devzone.nordicsemi.com/f/nordic-q-a/53073/unable-to-add-lte-device-on-nrf-cloud , can I check that...
The new SDK has no documentation on this functionality: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v12.0.0%2Fgroup__ble__radio__notification...
Where to get this RaspPi_OT_Border_Router_Demo_v3.1.0-1.alpha.img file.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0%2Findex...
Hello
I need urgent help. From days I have been stuck exploring NRF SDK 15.0 to do a simple task.
I am using an NRF DK board PCA10040. After going through peripheral drivers...
Hi,
I am working with central and peripheral uart example and facing with connection problem between two boards.After debugging at the central side i am getting error in...
Dear Sir/Madam,
We have a customer to develop a product based on nRF51422 and then they passed their product for pre-registration test.
They used DTM interface to connect...
Hello
I have nRF52832 custom board and have BME280 sensor connected to I2C/TWI
Whatever I do I get same reading (for 3 different sensors)
I'm constantly reading same...
Hello, I would like to use nRF24AP2 in a SPI bus with an accelerometer (a slave peripheral). I need that the host works as master with accelerometer. But in this way we will...
