Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
HI
We need stencil details for the above said chip, along with the details of pad opening for stencil, thickness, solder paste type to be used , reflow profile, & thing...
Hello,
I am using nrf52832 with PCA10040 and SDK15.1 along with a temperature sensor MAX30205. So far I can write, but I am realizing that I cannot read the second byte...
Hi, I'm using the nRF52840 SDK15.2.0 I'd like to get data from a digital microphone via a PDM interface. The teansfer data to speaker via a I2S interface.
Here is my problem...
I use the SES ver 4.12 with embOS of Segger.
It happened to me all the time.
I take an example from Nordic. I rebuild it with no warning. Then I take and add my files...
During the firmware running, there will be a HardFault_Handler error occasionally.
Is there any way to locate the error source?
Is there any good way to catch the hardware...
Hello. I have a problem with enabling nrfx module. I get this error during prohect compilation: 'NRFX_TWI0_INST_IDX' undeclared here (not in a function); did you mean 'NRFX_TWI_INSTANCE...
Hi,
I'd like to set 3 nrf52840-DK in the following way :
One device acts as central
2 devices acts as peripheral
I'd like the central to be connected to both peripherals...
I have custom board with nrf 52832. I am using SDK 12.3.0. and soft devices s132 V3.0.0 to transmit advertising packets with advertising interval 1s. I have written simple...
I already have a few devices in the field, and I'm curious if it is possible to occasionally update the signing key (e.g. to upgrade key, or compromised key, etc). If not...
Hello, I want to establish a connection between NRF52832 IC and ESP32 Module.
I implemented BLE on ESP 32 and achieved communication between Nordic Mobile app and ESP32...
Hi,
I am trying to used the WINC1500 Wifi module with the nRF9160 DK but I am not getting any data back from the module.
I am using the module
https://www.microchip...
Dear Nordic Support,
I follow this SAADC example to calibrate the SAADC every SAADC_CALIBRATION_INTERVAL.
However, whenever the function nrfx_saadc_abort() is called...
I am running into a strange issue. I want the bootloader to start automatically when I power on the device and then start the application if there is no activity after 30...
Hi,
If I want compiler my project at specified locate, the only thing tat I need to do is following image? Is it right?
After I program this program into address 0x0001D000...
I am trying to make PN7150 work with nRF52840 using TWI Communication.
Problem : PN7150 gets detected with I2C scanner example when using Adafruit Bootloader and programmed...
