Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
nRFConnect sees the j-Link device, and everyone else sees the device.
I use this j-Link with Segger Embedded Studio.
What makes nRFConnect unhappy? Perhaps python2...
Does nRF51822 support uart over ble profile? I see in previous discussion "nRF8001 UART-over-BLE" talking about this and answer suggest 51 serial has this?
We want add MQTT...
Hi everyone.
I have problem with my device. I use Visual studio with visual GDB and I'm trying to use interrupts from RTC. Got from this site lot of examples and wrote some...
Hi,
I am running my nRF9160 DK in "nRF Only Mode" (Via SW1). I would like to drive the serial terminal out via one of the GPIO pins, connected to my MAC using an FTDI serial...
SDK v15.2.0 using peripheral spi example. Windows 8.1, uploading to nRF52 DK.
In my while loop I use bma_spi_read() twice with a small delay in between. The first...
Hi,
I am using the reliable message communication to measure Round-trip time based on the Light switch example.
I noticed that in high traffics, some packets are not...
I want to use TimeSlot API for nrf52832.
two question.
I want to use time slots regularly . I call follow, timeslot_open() timeslot_request() - timeslot_end() -> IDLE_STATE...
Hi there,
I've already asked about it https://devzone.nordicsemi.com/f/nordic-q-a/49701/commissioner-disable and I've tried it but nothing work. I've already spent 5 days...
I am in pre production with the nRF52840. My customers have access to the micro USB port on the device. I want them to be able to define a string for the nRF5 transmitted...
I am using nRF51, SD 130 1.0 and SDK 10.0.0. I have 11 buttons connected to nRF. Currently it only works for up to 4 buttons (APP_TIMER_OP_QUEUE_SIZE is 4, but I'm not sure...
Hi,
i am working on spi master example in nrf52832, when clock is set to 8MHz, clk signal output at the nrf52 pin is more like triangle wave.
is there any way to set pin...
Hi,
At the moment, my current location does not have an NB-IoT network for the nRF9160 DK to attach to. This means that the device is unable to activate PSM mode (which...
Working with SDK 15 on an nRF52832:
I have a peripheral applicatin where I'm computing the value of a BLE read on the fly.
Currently I do that by:
Setting up a BLE...
Dear dev community,
I've got a very simple question: How can I see the subscription and publishing addresses list in any mesh node for any model?
Thank you!
Regards...
Hi I am developing a custom PCB for the nrf51822 chip. I heard the nrf51822 chips do not come with preloaded firmware or bootloader. Do I need to also flash the bootloader...
