Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I'm trying to obtain as much information as possible about my usb connection with Nordic chip. I'm working on DK board with nRF840, sdk14 and usbd_msc example. My problem...
Hi,
I am using a chip labeled with "N52832 QF ABB0 1717AQ".
According to its specification, this chip should have 256kB flash. However, nRFgo Studio shows that its size...
I'm currently using matlab to perform a non-linear least squares regression to fit a line to an array of samples polled from the ADC with roughly 100 data points. Is something...
Hello,
Did anyone succesfully used meshctl from Bluez with Mesh serial example? Looking at both it seems that it should be doable but the tricky part is figuring out the...
i use ble_app_uart to send data to centrol, and i don't need the UART peripheral, so diabled uart with it: NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
but the problem...
Hello,
I am working on the project through the BLE Multi-link Example.
In the description of the BLE Multi-link Example, "The central device can have a maximum of 8 concurrent...
Hi Nordic team
I have a question about Litepoint bluetooth advanced nRF5x OTA Testing.
According to the White Paper v1.0, by using the heart rate app, it is easy to evaluate...
Hi,
I am using the ble_app_uart_c example for the ble_central of SDK 12.2.0 to send data over UART to a nrf52832 based peripheral. When following the format as suggested...
i use sdk14.2 52832 as central , have bas service and myself service it have pair process , there are one change question. When I first burned the program, the bas service...
Hi,
I'm using Noble.js on a central RPi3 for DFU updates over BLE. The process is several times slower than doing the DFU over nRF Connect on an Android phone. I believe...
I am designing a NRF52 based device. One of the component , Crystal X1, EPSON FA-128 32.0000MF10Z-AJ3 used in the reference design is not available for purchase in online...
On the included Thing52 example, the LED fires m_ioext_osc_status_change from an interrupt. Eventually, when it comes to requesting use of the TWI this comparison happens...
I've noticed that if I call app_usbd_cdc_acm_write with the length set to any multiple of 64 the data will not show up on my PC until I do another write with a value that...
Hi DevZone,
I am modifying an CAN library for nRF52840 preview DK. In my project, nRF52 preview DK is working as a SPI master and Arduino CAN Bus Shield is working as a...
