Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi ,
We are using BLE nano board as a connectivity board and mDot board as application chip which is running on mbed platform.Connection deatsils are same as described here...
Hi,
I am working in one application in which I need SAADC to sample two channels at 1ksps and 500 samples per seconds.
I am sending 1 and 2 to switch the sampling rate...
After trying to run keil project after setting conditional breakpoit it raises error.
is it right that nrf52 doesn't support conditional breakpoits? or something wrong...
Hi,
I'm using the SDK11 and SD130 on a custom board which has a nrf51822.
I connected via SPI to a DSP that sends and receive audio.
My handler of the SPI is as it follows...
I'm trying to send a set of 246 bytes by uart fifo. I have a PC side which retreive the data, but I always miss some bytes (4 to 6).
I'm checking app_uart_put return and...
Hello,
I would like to use the nrf51822xxaa as BLE gateway for an ARM application processor (connected through the UART).
I successfully cross-compiled pc-ble-driver...
Hi..
Can i use both observer and broadcaster roles concurrently in s130 soft device..?
Is any TDMA needed to do this..?
Is it possible to do without stooping the other...
Hi,
I have read the S132 Softdevice specification v3.0 and just want to make sure that my interpretation is correct. There are two scenarios I would like to verify:
...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
When...
Hi,
As a beginner, I'm trying to have CDC J-Link Uart port work with my laptop. I'm using nRF52 board. When connecting the board to my laptop (windows 10), it displays...
Need some help on the tcp server example in the IoT SDK.
All steps working but the python script gets Connection refused.
bash# ifconfig bt0
bt0 Link encap:UNSPEC...
(nrf52832 PCA10040)
Hello. I'm trying to go along with the ble tutorial (advertising, service).
I download before last version of sdk 11 because with last 12 it's not working...
Hello everyone,
I have 2 chip; Bluegiga and nRF51-DK
I can easily advertise my custom service in Bluegiga chip. As you can see, nRF Connect application shows my service...
I think one way or the other the struct ble_gatts_evt_t must be correlated with the GATT profile, that is, ble_gatts_evt_t should have services and characteristics as its...
Hi,
> Context:
I run a baremetal application that I would like to enhance with bluetooth.
I am considering a BLE module from NS.
I currently have a SoC (nanopi...
