Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi:
Hardware setup: nRF52840DK interfacing with Adafruit LIS3DH (ST LIS3DH) over I2C on pins P1.14 and P1.15
Software: ncs-v3.2.1, Zephyr 4.2.99
Kconfig: I2C bus drivers...
I have a question regarding the nRF5340. I would like to capture and access the raw payload of BLE packets that fail the CRC check.
I know that with the nRF52840 (running...
I have a few doubts regarding power macros and getting the result I want. From combing through posts I have found the following: Since BT840XE has a FEM, you need to properly...
Hello Team,
Working on nrf54l15 using NCS SDK version 3.0.2 and tool chain version 3.0.2 Currently facing error while build. Following is the error
CMake Error at cmake...
We have engineers with newer android devices unable to install the nRF Mesh Sniffer app on newer android devices. The Google Play store says "not available for any of your...
Hi, I am working on a channel sounding positioning system using one initiator and 7 reflectors. Since concurrent channel sounding does not work, the program performs sequential...
Hi, I took my old NRF52840 DK PCA10056 revision 2.0.1 and tried evaluating it today after few years. I am unable to connect to the target. I have 2 identical boards that were...
Hi ,
We have a device running nRF5 SDK 16.0.0 with SoftDevice S332 (BLE + ANT). We use BLE Central/Peripheral links plus multiple ANT sensors. Under load we see frequent...
Hiya,
I am currently going through the nRF Connect SDK Fundamentals Lesson 2 (section: DK devicetree file) and I am stuck. In the example given, it says:
" These hardware...
It's great to have a public forum with Nordic engineers helping out but the DevZone web experience leaves much to be desired. The editing is painful enough that I really dislike...
We are using nRF54L15 devices and have enabled secure boot . Our current setup is:
Firmware images are signed with a private key
The corresponding public key is...
Hi,
I am trying to use lvgl on nrf54l15, but I am facing issues with spi. I was trying first to use vanilla zephyr 4.1, but now I switched to ncs 3.1.1. I am trying to run...
Hi
I'm using two nRF5340 Audio DK's for my university project. I'm just trying to familiarise myself with the audio examples by sending audio from one kit to another but...
Hello, I am facing an issue of low speed of file read and write while using LFS on External Flash, Winbond (W25Q64JV) .
This is the Configuration Im using in my DTS file...
Hi,
Just received a nRF52840 connected it to my Apple Silicon Macbook (maybe relevant?) which is running Sequoia 15.2 via a USB-C to micro cable.
When I powered it up...
