Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi support !
In my current application, I use nRF24L01+.
I want to change this nRF24L01+ for a nRF51422 to add BLE connectivity.
So, I've started my development with...
I'm using SDK 7.1, PCA10028 eval board, SD110 7.1, MCP 3.6.0.8331
I have 2 characteristics, and both are 32 bytes long. When I try a "Write Long" from the MCP a
BLE_EVT_USER_MEM_REQUEST...
Hi,
Merry Christmas!
I have a question about pstorage_store.
Actually, I want to store some data in the memory. Each piece of data has its own size (between 1 byte to...
Can I config AIN0 and AIN7 as the input pins of ADC, and config P0.01 and P0.02 as TWI, and config P0.03 and P0.04 as GPIO?
Or I must config ALL AIN PINS as ADC?
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi,
I've followed the steps mentioned in this thread devzone.nordicsemi.com/.../ and everything seemed to work fine. I've successfully uploaded "nrf51822_beacon_app.hex...
Hi.
I read in the sdk documentation, there is a library to use MPU-6050.
So i try to find it but I did not succeed.
i want to read data from 6050 and send this data with...
Hello.
I want to use nRF51422 chips to make some kind of mesh network using raw radio stack (NRF_RADIO) with my own protocol on the top of it. In reference manual there...
Hi,
I am a new comer to the nRF8001.
I am using Redbear Blendmicro (nRF8001) for my project.
I have wrote a apps to scan my Blendmicro(s) and acquire their RSSI value...
I use direct input AIN2 pin battery 3.3v, the other pins are not connected to anything, I did not enter into ADC_IRQHandler,may ask about what the problem it
this is my...
Has anything changed with the Bluetooth LE in iOS 8? I have an ANCS library for Arduino ( https://github.com/robotastic/ANCS-Library ) that was working fine with iOS 7. I...
I'm trying to program nrf51822 via st-link and open ocd.
Here command:
openocd-0.8.0.exe -f interface/stlink-v2.cfg -f target/nrf51_stlink.tcl -c "program address". ...
dear all:
I have 2 kind of board that are PCA10006 and PCA10028,
but I find out the IoT example can't be run on PCA1006,
what are different between PCA10006 and PCA10028...