Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Four returned products after sale could not be turned on & charged normally. Preliminary analysis of disassembly showed that the MCU was damaged, and the MCU was cross-verified...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hello All,
I have developed advertising init in 14.2 sdk (in segger ide).
(working on nrf52810 board)
I wanted to migrate same functionality to 15.3 sdk so how i can...
Hi everyone! I am using the STM32L4xx Sensortile to transmit accelerometer data from the Sensortile Acceleromter. The characteristics of other functions are shown on the nRF...
Hello guys,
I wan`t to make an project that send trough serial port a new image to flash my nrf9160.
By the moment I managed to send and recieve data but only on uart0...
Hi,
Iam running the BLE uart and zigbee light multi protocol example. Using the latest thread and zigbee SDK v3.2.0. The example is quite good. That the door(zigbee+BLE...
Hello,
Where do I find the plating material information for the following part numbers? is it Matte Tin?
Nordic Semiconductor nRF51822-QFAB-T
Nordic Semiconductor...
I design a 4 layer pcb which include nrf52832. But i'm unsure what rf trace width should be on 4 layers pcb?
This trace 30mil width and 5mil clearance for 2 layers pcb as...
Hi,
I am using NRF52. i have custom board on that external flash and SD card is not available. i want to use msc class so that i can drag and drop file and read it in controller...
Suddenly my app, running on iOS 7, is reporting lots of spontaneous disconnects by the peripheral device, an nRF51822, indicating a timeout:
didDisconnectPeripheral: Peripheral...
Hi !
I added " Read Characteristic" in NUS.
How can I get different values every time I click "read again"? For example, read the value of a varying ADC from here. ...
I am investigating increasing throughput in our application. Upon investigation both with our software and the ble_app_att_mtu_throughput example code. I found that there...
Hello! I want to develop such a functional: nrf52840 receives a line from my application that it saves to memory, and then, when I click on the button, it returns this line...
Peripheral: nrf52832
Central: nrf52840
The communication speed after executing sd_ble_gap_conn_param_update is different in the following two cases.
case 1:
...
Hello
I am trying to do BLE communication using nRF52832. I wrote the exact same program on a module (BLENano2) with the same nRF52832 chip, but one was able to do BLE...
Hi.
- Is it the case that before every write to persistent storage via nrf_fstorage_write, the page written to has to be erased first (via nrf_fstorage_erase) since only...
