Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
We have a firmware developed for Full Thread Device. But now as i want to reduce power consumption i want to convert FTD device firmware to SED firmware.
SDK...
After reading this https://devzone.nordicsemi.com/f/nordic-q-a/3830/what-is-the-value-of-the-gpio-pull-up-and-pull-down-resistor
and seeing that the internal pull-up is...
I'm trying to get readings from an LPS22HB sensor with the nrf52810 using the lps22hb driver in SDK 17.0.2_d674dde.
The lps22hb_init() call completes without any errors...
Hi, I'm using nRF52805 and SEGGER.
The firmware could be programmed to the chip successfully when I use Debug->go. I can connect with the BLE signal.
However, when I use...
Hi! I am struggling with figuring out how to properly set the sampling frequency for the qdec device. I noticed that making changes directly to the members of config struct...
Hi,
I'm setting up SAADC as explained in the examples: First start conversions with buffer 0, then with buffer 1. On the SAADC callback I queue the current buffer for conversions...
I'm developing an app that communicates with iOS apps using Nordic's services.
I got this error during development.
I have three questions about the "peer removed pairing...
Hi,
I want to enable 8 channels of saadc in SE mode with 10 bits of resolution. the number of samples in every packet is 32, which means every channel have 4 samples in...
The problem I meet similar to https://devzone.nordicsemi.com/f/nordic-q-a/60684/nrf5340-pdk---debugger-in-ses-remains-in-bt_enable-forever .
/* Wait til nameservice ep...
I'm interested in collecting the modem core temperature for my applications. After some digging in modem_info.h / modem_info.c , I saw the temperature data structure exists...
I want to use PPK2 to test the power consumption of my user device, I have connected the PPK device to my pc with USB cable and turned on its power switch, but when I opened...
Hi, I am trying to run the sample I2S echo program(nrf-sdk/zephyr/samples/drivers/i2s/echo) on 9160 DK, and am having issues reading any valid data on I2s RX. Codec chip is...
Hello
NRF52840 with own hardware
nRF SDK V17.0.2_d674dde
nRF SDK for Mesh V5.0.0
IDE: SEGGER 5.60
I started with the "ble_peripheral/ble_app_template" example...
I am trying to use the dongle as a BLE sniffer. I have followed the directions on how to program the dongle including downloading and installing the jLink software.
When...
SDK 17.0.2, SD 7.2.0. with secure bootloader, when performing DFU without BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE, nRFConnect will successfully update the app. With BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE...
