I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi there,
My current setup:
1. Custom board.
2. SDK nRF5 SDK v17.0.2
3. Application running BLE (SoftDevice)
Using the USB CDC Class example to be able to interface...
I'm using nRF51 sniffer to capture BLE packets for group of devices. Sniffer can able to capture only primary advertisement channels and not secondary advertisement channels...
Dear Members,
I want to use this code :
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk51.v10.0.0%2Fant_examples_bpwr.html
Does it work...
Excuse me:
As shown in the figure below, can this type of crystal oscillator be used on nrf52832? How to connect this crystal oscillator with XC1 and XC2 of nrf52832?
Hi,
we are preparing for certification and are about to test with the DTM v1.0. now in nAN43 it states following:
1.1.1 Hardware requirements • nRF8001 Development Kit...
I try to add pairing/bonding to the NCS hello world project. But I found the information is not easy to find. I'm playing with the bt_conn_auth_cb struct to understand how...
Hello,
I am trying to verify a signature with the `NIST p-256` curve. I had previously done this with the Nrf5 sdk and it is working:
I am now trying to migrate...
Hello Nordic Team,
as a newbie in the Nordic world, I have been reading the nRF Connect SDK and Zephyr documentation as well as testing some of the samples on my nRF5340DK...
Hi.
I have some trouble to use a sensor based on JDY-23 module with nrf52832 dk
(JDY-23 datasheet : ://fcc.report/FCC-ID/2AXM8-JDY-23/4936741.pdf )
We tried to connect...
Hi,
Is LLPM over the air compatible between nRF52840 and nRF5340 devices?
I am aware that LLPM is not fully supported yet on nRF5340. Also, any update on the LLPM support...
We are hearing solder bridge issues on the NRF52832-QFAA:
"Due to the high thickness of the copper layer and small lead spacing on the component, the boardshops are not...
I am working on customizing the DFU bootloader (to add encryption). When attempting to use the instruction trace in Ozone to debug, I see a lot of nonsense. One example is...
I've been analyzing various nRF52 devices and noticed that there is an inconsistency with vendors using Legacy DFU and Secure DFU. Or in other words, there doesn't seem to...
