I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello Devs,
I am facing an difficult time to write a custom opcode to a QSPI flash memory. where I am trying to read the manufacture ID, it requires send the OP code + Address...
Hi, We are looking for a Suitable wireless technology for Video transfer(Video Transmitter and receiver)
Main Constraint: - From Power Up-->Boot-Up time of Wireless transmitter...
Hello,
We are looking for a 2.4Ghz supported module with Programmable Frequency Deviation. Is there a product that we can consider from Nordic Semiconductor for this?...
Hi, We are working with integrating LoRa to our nRF52840 with BLE and FreeRTOS. To be sure that LoRa worked as expected, we configured and tested LoRa on nRF52840 dk and observed...
Hello,
I'm using nrf52840 and i would like to ask if it possible to use the I2C bus without external pullups. I mean, i would like to avoid using external pullups
is there...
I am using a NRF52840 DK with a SoftDevice S140 6.1.1. I have also flashed the secure ble bootloader on the device.
I have been using the nrfprog command line tools within...
Hello,
Got the MQTT_SIMPLE to work and the sensor samples from zephyr also, however, how can i mix the 2 to have the mqttsimple with some gpio and i2c sensor ? how will...
Hi
I have installed every requirement for the device. I want to know how to run the blinky example on the device. I can not find the SDK which has the example plus can I...
Hello, I'm currently developing a PS2 code to read the inputs of a mouse and transmit it over BLE, nrf_delay_us() is giving me a fatal error every time according to debug...
Hi,
I am trying to implement Generic HID that can transmit/receive data like CDC using the generic HID example source of nRF52820 SDK 17.0.2.
But I can't do both sending...
Hello everyone,
I'm a fresher of nRF52833. I'm facing a problem like this:
I want to read some information in Terminal but In my product I only have USB I/Os (D+ D-)....
Hi,
I'm trying to use the nRF91 as a Modem for an Arduino. Is there some example on how to use the AT commands of the serial_lte_modem sample to send a HTTP (or at least...
I built an application for the nrf51822 on top of SDK12.3, to which I added the buttonless DFU based on the "experimental_ble_app_buttonless_dfu" example.
As a boot loader...
Hi,
I want to increase the amount of BLE MIDI packages I am sending. Softdevice 132 nrf52832
MIDI data is sent by notifications and updates of the characteristic value...
Hi,
I want to use uart async on the nrf9160, I get the following linking errors at build time:
here is my prj.conf
If it's defined CONFIG_UART_INTERRUPT_DRIVEN...
