Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hello, I'quiet new in Zephyr.
So tell me if I'm wrong.
I would like to test driver mcp23s17 present on zephyr.
I've add in .overlay file
And now I want to initialize...
Hi all,
I'm programming nRF52833 with SDK17.
I want to use only one channel (for example 37) to broadcast advertising during advertise interval and also one channel of...
My team was looking to transfer a 20-byte value (or 'message') between a mesh client and server, what is the best way to achieve this? I have practiced with the light_switch...
Hi,
I am currently developing an application for the NRF52840 using a custom pcb powered through the VDDH pin using a 4.2v lithium ion battery. Part of my application requires...
Hi,
I am trying to following the instructions at: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_user_guides_java_coaps...
I have configured the dev kit by cutting the SB9 bridge. I am powering the device from the J2 USB port on the DK. I have not bridged SB12 or SB11 as I am powering the device...
Hello all,
I am experiencing a ~5uA oscillation (between 5uA and 10uA) in sleep mode, DC/DC converter enabled, no RAM retention. The total current is of the entire system...
i am working with jlink segger edu, in a custom board, it dont have swd TX, RX pins connected, only jtag pins. I Need to see if my gps conected throw uart is working or not...
I configured the pca63519-sr3_nrf52832_shield to fit on my board (actually disabled all peripherals, only the bluetooth protocol part), but found that the modified code could...
Hello! I wrote about the details in topic 66156 , but they did not answer me, because this question is already different from the original one. The drv_rtc.c library has this...
HI,
I have been facing a few issues with the BLE custom service, I am looking to create a Pedo meter service which displays step count information received from the sensor...
Hi Guys,
We have designed a custom board which is using BMD350.
Our application requires using the BMD350 in beacon mode and then going to sleep in low power.
We have...
I can listen for radio inactive event according to this post https://devzone.nordicsemi.com/f/nordic-q-a/9137/change-advertising-every-time-event but I am scanning at the...
Hi everyone,
I want to assign the DEVICEID to System ID characteristic (which is under Device Information Service). DEVICEID is a 64bit and I found that I could assign this...
Hello,
I am developing a sensor like a beacon. I want to measure the distance from the node. I record the RSSI sample for a few seconds and average it to stabilize the value...
