Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I have a usb dongle with nRF51422 (PCA10031) and downloaded nrf sniffer software version 2-beta from https://www.nordicsemi.com/eng/nordic/download_resource/65225/1/90637756...
hi,
i am using NRF52832 DK, and sdk 15.0.0.0 ,,
i want make the central to work also as a peripheral...i.e whenever central is not working ,or ,central is not in connection...
I am evaluating the throughput of BLE communication between 2 NRF52832's, 1 acting as a central and 1 as a peripheral. I've modified the ATT_MTU Throughput Example, and I...
Gone through sdk 11.0.0 Experimental_ble_blinky application, i trying to assign one gpio pin in place of connected LED. what is it receiving when pressing on & off switch...
Hi,
I'm working with nRF52832 chip following the example "ble_app_beacon". I see the advertising packet is limited to 31 bytes only. However, I'd like to take an advantage...
Hi,
I have arm based application processor and need to connect with nRF52840 using UART, I don't have any idea about bootloader and factory firmware when hardware assemble...
We are trying to determine the emission designator for the nRF52832, or at least to determine the necessary bandwidth so that we can create the emissions designator. Please...
Hi everyone,
I have a problem with SOME android devices.
In particular Android devices with BLE 4.0 & 4.1, but I have NO problem with Android device with BLE 4.2 and iOS...
Hello,
We are using nRF52832 DK with SES IDE and latest SDK 15.0 sd 132. We have developed one multiplink central device and modified ble_nus_c with our application to connect...
I use nRF52832,is 2.5v power supply,but you can't download the program,w hen I set the voltage above 2.8v, I can download the program,then I switched the voltage to 2.5v and...
Hi everyone
I am able to send the data over the UART to the Real Terminal and also to my other device working on UART protocol. However , I am not able to read the data...
Hi,
I am willing to migrate sdk 14.2 code to sdk 15.0 code. Do you mind me to ask a crypto micro-ecc question, please? Thanks.
In sdk 14.2, the micro-ecc part definition...
Hi,
I am working on nRF52832 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
When I am trying to initialize a structure in Flash memory, the...
I'm developing TWI code for Bosch BNO080. They use SHTP protocol on top of TWI. A working version using Wire library of Arduino is posted here .
I ported the code, and...
Hi there,
I'm playing around with the stock hrs_relay example that I've modified. the code works well but I'm noticing that its advertising strength is crazy high.
I was...
