I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Dear friends,
If i set the conection interval=100ms and the slave latency=1, the slave will wake up every 200ms. If the slave has data to send, it will still wake up every...
I haven't been able to find a drawing file for the nRF51 Development Kit. Is there one out there?
Ideally, I'd like to get the drawing and a *.STP file for SolidWorks.
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
The file nRF5_SDK_1 4.2.0_17b948a/components/libraries/util/app_error_weak.c requires the following modification to correctly compile: Add: #include "app_util_platform.h"...
Hi,
I'm currently using SDK v14.2.0 and I'm attempting to merge the buttonless DFU bluetooth example into the bluetooth template project within the Eclipse Oxygen environment...
Hey Guys,
I have 3 tasks running on FreeRTOS, SDK v14.0.0. In each task, I want to use SEGGER_RTT_printf() to debug.
I currently just call SEGGER_RTT_printf() without...
I have two nrf devices nrf51822 and nrf52DK, In nrf51822 i'm using S110 and i had created a custom service with 10 characteristics. If i connected to nrf connect i can able...
Hi,
Is it possible to make realization of this protocol ( wiki link ) with softdevice? After reading forum I think "more no than yes" because softdevice blocks CPU and this...
Hello
I am still relatively new to microcontroller development with the NRF52 DK. I am currently running a modified version of ble_app_uart__saadc_timer_driven__scan_mode...
I have a Taiyo Yuden Evaluation board , with EBSHJNZXZ completed with Segger and j - link , when load the project in board, not have any error debug, the sketch is load successfully...
I am following this tutorial
I'm using Segger Embedded Studio v3.10i, and SDK 12.2.0. I have the exact same problem in both Linux and Windows.
I have done everything...
What are the details of internal pin connection circuitry when connected as GPIO/IRQ vs ADC vs Comparator? Is there an internal pull down (what value)? Is there internal diode...
what should be RAM Settings for 51822QFAA chip?
I am using nrf sdk for mesh. what should be required ram settings for 51822 in order to run light switch server example....
Hello,
I have problem with missing GPIOTE event. Sometimes event doesn't occur, sometimes there is no problem. This event is very rare but important. I think it happens...
