I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
This is kind of a follow-on to the original question here: devzone.nordicsemi.com/.../
I notice that the nRF52840 PDK dev boards need to be closer at the beginning of the...
Hi!
I am sending the battery status every 1sec from nRF52840 peripheral device and receiving it on nRF5240 central device. (verified the battery status working through...
Hi,
I am unable to read values from ADC pins, usiing nrf51822 nordic bt module, s130 softdevice.
Things I dont know:
Connecting to ADC pins
readings from the pins...
Hi,
If I set the tx buffer to 0 before and transaction, I expect the spi slave register's AMOUNTTX to be 0 when the transfer complete. But intstead, the AMOUNTTX always...
I'm working with a sensor that communicates over spi, but it uses a single wire for miso and miso. Is there any alternative to just bitbaning the protocol? Specific sensor...
Hello.
we are using the nrf51822 and doing the approval of the radio transmitting equipment model.They refer the modulation mode,as the picture:
I am asking:1、can the modulation...
I'm working on a central device. I'm using 52832, SDK11, SD2.0.0
I accidentally used a peripheral device that doesn't have the right service UUID that my central device...
I'm using nrf_delay_ms to trigger a series of beeps though a speaker using PWM, but I seem to have intermittent problems with this when the device is connected.
Basically...
I am trying to get fstorage to work, but I seem to miss some of the symbols needed: "error: 'NRF_EVT_FLASH_OPERATION_SUCCESS' undeclared". These are declared in softdevice...
Hi all,
I am using a BLE nano 2, which is based on the nRF52832. I am trying to measure small capacities of a few pF with this method:
wordpress.codewrite.co.uk/.../...
I want to connect a central and peripheral and only have ble on when the peripheral senses a certain event that exceeds a threshold. Do the devices need to connect on startup...
Hi Nordic,
I’m H/W engineer, dedicated in development of radio circuit. I ask the question because we’d like propose your Nordice nRF52840 to our customer when replying...
I am developing an application which uses 2 nrf52 running sdk 12.3 and softdevice 132 V3.
The central device appears to be saving and whitelisting the two peers, but it...
Hello!
We designed and manufactured board with nRF52832_QFAA. The NFC pins was configured as IO and connected to sensors. The problem is that we see that those pins get...
