Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello. I have a question about how to enable a 32 MHz crystal oscillator on a custom board? I have 32 kHz and 32 MHz quartz crystals on the board. I found the following config...
Hi. This is a problem that occurs on a customer's factory test client unit. Issue occurs roughly about once every few months.
Customer Development Environment Info:
OS...
Hi,
I am stuck during migration from ncs 2.6.2 to 2.7.0 (I want to finally reach 2.9.0):
``` [00:00:13.276,275] <err> bt_sdc_hci_driver: SoftDevice Controller ASSERT:...
Dear customer support people,
I'm trying to employ a particular signature scheme to benchmark it against other more traditional methods on your devices, specifically on...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
Kicked off an application FOTA update, and somehow it failed:
[00:02:06.161,315] <err> download_client: Error in recv(),...
I've built a firmware based on the hci_uart sample with the softdevice controller. The board is custom made and has a nrf52840 on it. Over USB-CDC HCI commands are sent to...
Is there any issue with using the nRF52833 DK/nRF52833 for Matter development? I’m asking because the Matter template doesn’t seem to support the nRF52833 DK/nRF52833. If...
Dear Nordic People Recently I am following YouTube link from Nordic Semiconductor for Implementing ESL https://www.youtube.com/watch?v=VeLkptpSvRQ This video requires specific...
Hello and thanks for reading. Also happy holidays.
We are using an NRF5340, and are having some issues with connectivity. I would therefore welcome any suggestions you may...
Hello
I've been experimenting in increasing the number of targets that a mesh FOTA distribution server can support on nRF52840
The CONFIG_BT_MESH_DFD_SRV_TARGETS_MAX has...
We want to upgrade our existing product to WiFi 6. We have a lot of customization in our TCP/IP stack so we don't want to use the zephyr stack. We only want to make the station...
While in the field test phase of our custom nrf9161 based device, we figured out that there are some towers of some providers that make the device seem online although it...
Hello,
I need to use the Radio_test example on a custom board using the nrf52810. I am using the nrf connect SDK 2.5.1 with VSCode.
To use the Radio_Test example I need...
Mesh 1.1 Generic Location Server defines special values for long/lat and north/east when unconfigured. Current code doesn't appear to support/use these special values, instead...
Hello everyone,
I am developing a ble project that builds on the peripheral Uart example using the sdk 2.4.0 for nrf5340.
I want to implement a watchdog since I sometimes...
