I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I am following the guide on this page: https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
I can build the firmware, but having trouble...
1， The SDK is nRF5_SDK_14.2.0_17b948a;
2, running the usbd_audio project; It don't control the volume by 52840;
3, Can you help me how to adding the volume control in...
We tried two build options:
1. thread version 1.1 with
# Set OpenThread NCP architecture CONFIG_OPENTHREAD_COPROCESSOR=y CONFIG_OPENTHREAD_COPROCESSOR_RCP=y
CONFIG_OPENTHREAD_THREAD_VERSION_1_1...
Hello
I'm using sdk v17.0.2 and I'm going to program using nrf52840 dongle.
I used nrf52DK because I didn't have nrf52840DK. And I'm going to upload the source code that...
Hi!
I am running Zephyr sample application for direction finding zephyr/samples/bluetooth/direction_finding_connectionless_rx with minor modifications on nRF52833 DK. I...
Hello, I'm developing a BLE application under nRF51422 based on SDK12.2 using softdevice S130. Now, I'm porting the application from Keil to IAR 8.11. There is no compilation...
Hi,
SDK nRF5_SDK_17.0.2
Using :\examples\peripheral\saadc
I want support for multiple peripheral in same project, so i took the saadc example and on top of it add Uart...
Dear Devzone,
We are testing GPS of our products based on nRF9160.
When we test in one car, the GPS signal is lost when the device is put inside this car. This situation...
While testing DFU for OTA ,after entering bootloader mode on my nRF52840 DK, the device doesnt show up either in the device manager or using nRFconnect and Jflash lite . when...
I've 3 FTD nodes (nRF52840 SoC), the network between the nodes and the UDP message transfers are been done successfully.
I want to split and send the messages between...
Hello,
I am using your NRF9160 chip and need Nordic team help. I have refer to your FOTA sample, I am looking for a safer solution for updating code. On my board, I use...
Three software seems to perform OTA DFU: nrfutil command line, nRF connect from desktop, nRF connect from mobile
Do I need all three of them? Are they part of Nordik SDK...
Hi,
I am using an Adafruit nRF52840 Express with a sensor board attached to it. I'm noticing that my sensor IC is reading about 3-6dB higher noise in the 10-50Hz range ...
Hello,
I want to program and debug a custom PCB using the nRF52832 SoC and nRF52 DK. I plan to use this setup:
From what I understand, the GND detect will cause the...
Hi Nordic team,
We are busy testing the throughput of the nRF9160. We are having issues installing the NCS at this stage, and was thus provided with a HEX file of the Serial...
