Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi all,
I am using the Adafruit Feather nRF52840 as my central device. My peripheral is a nRF52832 with a 9DoF IMU. (SDK17.02)
I need to stream 26 Bytes of IMU data at...
Hello,
we started using zephyr OS for our firmware projects. To implement a propriety protocol on top of IEEE802.15.4 I use the radio with CONFIG_IEEE802154_RAW_MODE =y...
Hello
I am using sdk v17. I am merging the example of ble_app_uart and crypto_aes_ctr.
I added files about crypto and set the file path. However, the path error is printed...
Hello~
I am experiencing hardfault occasionally. (once a day ~ once in 3 days)
I am testing 14 boards to catch hardfault.
The following is my setup
- hardware...
Hello, I was trying to run the sample Alexa Gadget Application on my NR52840-DK, using nrf Connect SDK v1.5.0. However, upon trying to run the application I am getting the...
Hi support team,
I am developing a product. The product needs read adc and restart advertising when no connection.
I get hardfault randomly when called the ble_advertising_start...
Hi all, the application i'm using nRF52810 for requires that I keep the device powered on all the time. However, in the case of errors (tolerable within my application) I...
I successfully compiled the micro_ecc library, but when I try to compile the project with it, I get an error. Has anyone encountered this? What can be wrong?
Build target...
We use the nRF5340 D version IC for one project, but the PCBA (main chip is nRF5340) not working, we can burn the hello_world.hex by Jlink 7.23 version, But the Crystal 32...
We are implementing on nRF52840 with latest NCS version the following code:
The nvs_init() function is halting due to an error at flash_sync_mpsl.c within nrf_flash_sync_exe...
Hello,
We are working on the nrf52840 custom board in that We trying to update firmware via DFU.
Problem definition : First we update firmware via DFU application boot...
Hi ,
We have a custom hardware with an Active GPS Antenna (that is connected to the main board with u.fl connector).
I ran the GPS SNR command to test the performance...
I'm designing a PCB that uses the nrf52832 with an external RTC, the DS1339 ( https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf ). I want to use a single 3.3V...
I'm enabling external power off warnings, as specified in section 5.22 of the AT command guide.
When I drop the supply voltage I see a LTE network disconnected message from...
