Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
I am unable to find how is software interrupt generated for Softdevice.
I am able to see SD_EVT_IRQHandler()
but when this event is triggered
Sudhir Foujada...
Hi,
I am using sdk for mesh V.5 and nrf52840 dk.
I have run the serial mesh example and it worked fine.
I also modified the light switch example to send and receive...
Hi, I tried using the border router example that is provided and it works ok. I would like to install the border router software right onto a machine running ubuntu so that...
Hello! My device (peripheral) is based on nRF52840. Also, I use nRF52840 DK (central) to establish connections from the Linux side and getting of the data from the device...
Hi all,
is it possible to have the Immediate Alert client and Server at the same time? I need to have an alert from Smartphone and also to be able to send an alert to the...
Hi
In the final SLM version , please provide an option to disable and enable JTAG in software (thru AT command or by some means)
As part of security, this is needed...
Hi,
We are in the process of integrating a NRF52840 to a linux based host gateway device, which is supposed to be the gateway for another peripheral device which also run...
nrf52 dk board TWI SCANNING EXAMPLE INTERFACING WITH EXTERNAL EEPROM
Hi, this is vadivelan
I am working on a task like interfacing external EEPROM memory with nrf52dk...
Hi,
I am currently trying to a DFU where the firmware image is sent to external memory, validated and then copied to flash and executed there. I am doing this with the nrf52840...
Hi while implementing Media Transfer Protocol MTP I wanted to know how many bytes were transmitted by the host on EPOUT. I had to do a bit of research and trial/error - I...
Hi,
SDK : nRF5_SDK_15.2.0_9412b96
I want to perform pairing between mobile app and a device NRF52832 device based on the device serial number.
In other words I want...
Hello,
I come to you because I wanted to recover the GPS data in my project for that I based on the sample agps, however when I launch my project at the time of the reception...
Hello
I had integrated the DFU client stack in ble_thread_dyn_hrs_coap_srv_freertos project.
SDK : nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8
After clearing all the...
I send AT command:
AT+CPSMS=1,"","","10100010","00100001" Which means active PSM mode with TAU time = 2 minutes, RAT = 1 minutes. I receive: CEREG: 1,"61E6","090A8C15",9...
