When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi,
I am using a custom board that uses Arm Cortex-A7 and embedding an nRF52840, There is no external low-frequency crystal 32kHz connected to the nrf52 chip, so I've enabled...
Hi ,
I'm trying to use http_application_update , on an https website, and i get:
I: Attempting to connect over IPv4 I: Setting up TLS credentials E: Unable to connect...
Hi,
I want to transmit data on each button ( lets say 4 buttons for now ) press on my custom board. I have used ble_app_beacon example and tutorial https://devzone.nordicsemi...
Hello
I have uploaded USB CDC ACM example code in my custom board of nRF52840. I didn't get Vcc on D+ pin and cannot detect USB. I have also check soldering side and resistance...
I have an si7055 i2c temperature sensor connected to an nRF52840
I've tried my best to get a reading, but failed.
Therefore given up.
I'd be grateful for some help to...
Hi,
We are starting a new development for an Ultra Low power product.
Thus, we found the nRF9160 as a good option with its ARM-M33 subprocessor. However, we have some...
Hi,
I'm having trouble with the BLE_GAP_EVT_DISCONNECTED event. I have an nRF 52832 running the SDK 15.2 as peripheral and have tried several devices as centrals (not simultaneously...
We are using the Zephyr IIS2DLPC driver to talk to that sensor from an nRF5340. This driver uses the Zephyr GPIO API to configure interrupts, which is implemented in drivers...
Hi,
I want to use nrf52840 dongle as a provisioner to provision other server and client nodes. So, i was trying to program dongle by using seggger and building and running...
Hi,
I am currently trying to create a bootloader for a project I am working on. I am familiarizing myself with the dfu and bootloader modules by running one of the example...
Currently I have implemented Central using nrf52810, SDK 14.2 / Softdevice S132.
I want to know how to do OTA upgrade in Central.
Or I would like to get an example currently...
What's the proper way to turn off BLE to conserve power?
I have a board with DC power input and battery backup. When the DC power fails, I want to finish what I'm doing...
I have an nRF 52832 running the SDK 15.2. I have a few general questions because I'm seeing behavior I don't understand and doesn't seem to be right.
If I erase all the...
I am attempting to load up the default NRF project "AT_Client" located at ...\ncs\v1.4.2\nrf\samples\nrf9160\at_client project, however, whenever I attempt to load it with...
